Menu
Sealey AL301.V2 Manual
   |
EOBD CODE READERMODEL NO: AL301.V2Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY WARNING! To prevent personal injury or damage to vehicles and/or the scan tool, read this instruction manual first and observe thefollowing safety precautions.9 Always perform automotive testing in a safe environment.9 Wear safety eye protection.9 Keep clothing, hair, hands, tools, test equipment, etc. away from all moving or hot engine parts.9 Operate the vehicle in a well ventilated work area. Exhaust gases are poisonous.9 Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.9 Use extreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These componentscreate hazardous voltages when the engine is running.9 Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brakeis engaged.9 Keep a fire extinguisher suitable for petrol/chemical/electrical fires nearby.8 DO NOT connect or disconnect any test equipment while the ignition is on or the engine is running.2. INTRODUCTIONCompetitively priced EOBD code reader. OBDII/EOBD compliant vehicles Petrol 2001 & Diesel 2004 onwards. CAN enabledretrieves generic P0, P2 and P3 and U10 codes and picks up manufacturer specific P1, P3 and U1 codes. This easy to use tool willthen turn off the MIL light, clear codes and resets monitors. Supplied with comprehensive instructions.3. FUNCTION DESCRIPTION1. LCD DISPLAY: Indicates test results. Backlit, 128 x 64 pixel display .2. ENTER/Exit BUTTON: Confirms a selection (or action) from a menu.or returns to previous menu3. SCROLL BUTTON: Scrolls through menu items or cancel an operation.4. OBD 11 Connector: Connects the scan tool to the vehicle’s Data LinkConnector (DLC).4. VEHICLE COVERAGE4.1. LOCATION OF THE DLC4.1.1. The DLC (Data Link Connector or Diagnostic Link Connector) is the standardized 16-cavity connector where diagnostic scan toolsinterface with the vehicle's on-board computer. The DLC is usually located 300mm from the center of the instrument panel (dash),under or around the driver's side for most vehicles. If Data Link Connector is not located under dashboard, a label should be theretelling the location. For some Asian and European vehicles, the DLC is located behind the ashtray and the ashtray must beremoved to access the connector. If the DLC cannot be found, refer to the vehicle's service manual for the location.4.2. OBD 11 DEFINITIONSOBD II Diagnostic Trouble Codes are codes that are stored by the on-board computer diagnostic system in response to a problemfound in the vehicle. These-codes identify a particular problem area and are intended to provide you with a guide as to where afault might be occurring within a vehicle. OBD II Diagnostic Trouble Codes consist of a five-digit alphanumeric code. The firstcharacter,a Letter, identifies which control system sets the code. The other four characters, all numbers, provide additionalinformation on where the DTC originated and the operating conditions that caused it to set.Original Language Version© Jack Sealey LimitedRefer toinstructionsWear eyeprotectionAL301.V2 Issue 2 (3) 09/03/23 |
Related manuals for Sealey AL301.V2
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved