Sealey ADT3 Instructions Manual

Also see for ADT3: Instructions

instructions foradjustable gearbox supportmodel no: adt3thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. saFetY WarNINg! ensure all preliminary checks are carefully carried out before using gearbox support and jack. Immediatelyrepair or replace damaged or missing parts (use an authorised service agent). ensure use of genuine parts only.unauthorised parts may be dangerous and will invalidate the warranty. WarNINg! Follow the safety instructions issued with the transmission jack.9 Before use ensure the transmission weight and size do not exceed the capacity of the gearbox support or the jack. WarNINg! ensure load is placed level and centrally on gearbox support and is fixed in place before attempting to lift,lower, or transport load. always use load restraint chain and attachments to stabilise and secure the load to the gearboxsupport.8 do Not use the gearbox support without restraint chain.8 do Not replace the chain with an inferior form of restraint.9 care should be taken when using the gearbox support and vertical transmission jack in conjunction with a vehicle lift to ensure that thevehicle is not lowered whilst the jack is in position.8 do Not move the jack, with or without a load, with the gearbox support in the raised position.8 do Not use the saddle for any purpose other than for vehicle transmissions.9 Before storing ensure gearbox support is clean and free of grease and oil.2. INtroductIoNthe Adt3 adjustable gearbox support has a rated capacity of 500kg and has been manufactured to a high specification to fit sealey Verticaltransmission Jacks, in place of the standard fixed saddle, thereby increasing the range of transmissions which can be accommodated. A fully adjustablesaddle with forward, backward and side to side tilt.3. specIFIcatIoNmodel no: ....................................................................................Adt3Applications: .................. 300GA, 300tr, 600GA, 600tr, 1000GA,............................................................................. 1250GA, 1250GtA(An adaptor, part no. Adt3.23 is supplied to fit the support to the 300tr.)4. asseMblY WarNINg! failure to assemble the gearbox support correctly may result in serious damage and/or personal injury.4.1. unpack the product and check contents against the parts diagram. should there be any damaged or missing parts contact yoursupplier immediately.Note: numbers shown in brackets refer to item numbers on the parts diagram.Note: items 14, 15, 16, 17, 18, 19, 20, 21 and 22 have been pre-assembled.4.2. Attach brackets (8) to the saddle (14) using bolts (10), washers (6) and nuts (7).4.3. Attach plates (5) to brackets using bolts (9), washers (6) and nuts (7).4.4. Attach chain (12) to one plate using bolt (13), washers (3) and nut (11).4.5. fit screw (2) to diagonally opposite plate using washer (6) and nut (7).4.6. slide hook bolt (1) through screw (2) and fit washer (3) and wing nut (4).5. operatIoN WarNINg! do Not use gearbox support if any suspect part is found, or if it is believed to have been subjected to abnormal load orshock. immediately remove from service and contact your authorised service agent. WarNINg! Always read, understand and implement these safety and operating instructions supplied with the gearbox support andthose supplied with the jack.5.1. With jack fully down remove existing fixed saddle and fit theADT3. ( An adaptor, part no Adt3.23 is supplied to fit the Adt3 to the 300tr.)5.2. Adjusting the pitch and tilt of gearbox support will assist you to safely support and transport the transmission. the gearbox support may be tiltedforward, backward and side to side by operating the appropriate handles (22). WarNINg! After adjusting the angle of the gearbox support always make sure that all four adjusting screws are in contact with the underside ofthe gearbox support. this will ensure that the gearbox support does not move during use, which would endanger both the transmission and theoperator.refer toinstructionmanualWear safetyfootwear Wear protectivegloves WearprotectiveclothingAdt3 | issue 2 (i) 31/01/17Original Language Version© Jack sealey limited

/ 2

Related manuals for Sealey ADT3