Sealey ADBLUE TP6809 Instructions Manual

ADBLUE® LEVER ACTION PUMPMODEL NO: TP6809Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY WARNING! Ensure health & safety, local authority and general workshop practice regulations are strictly adhered to when using thisequipment.9 Familiarise yourself with product application and limitations, as well as the specific potential hazards perculiar to this product.9 Maintain pump in good condition. Use an authorised service agent.9 Replace or repair damaged parts. Use only genuine parts only. Non authorised parts will invalidate warranty.9 Pump is specifically constructed with Viton seals for transferring AdBlue (diesel engine fuel additive).9 Can also be used with water, antifreeze, windshield washer fluid or mild detergents.9 Ensure safety eye protection, protective clothing and gloves are worn when using this product.9 Keep the work area clean, uncluttered and ensure there is adequate lighting.9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip footware.9 Keep children and unauthorised persons away from the working area.9 Dispose of waste liquids in accordance with local authority regulations.8 DO NOT use to extract corrosive fluids.8 DO NOT dismantle, tamper with or adapt the pump for any other purpose other than for which it is designed.8 DO NOT use the pump if it had been dropped or mishandled. Check the pump to ensure there is no damage.8 DO NOT use the pump as a handle to move the fluid drum.9 Keep the pump clean and store in a safe dry, childproof location. WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment.2. INTRODUCTIONLever action pump specifically for use with AdBlue®. The dip tube extends from 350mm to 980mm to fit 100L, 205L drums orbarrels, or 1000L IBC tank. Specially constructed with Viton® seals for transferring AdBlue®. 1.6m Delivery hose for hands-freeapplications.Approximately 500ml per stroke discharge. Can also be used with water, antifreeze, windshield washer fluid or mild detergents.3. SPECIFICATIONModel no: ...................................................................TP6809Delivery volume: .............................500ml approx. per stroke4. ASSEMBLYUnpack the product and check contents. Should there be any damaged or missing parts contact your local supplier immediately.4.1. Dip tube assembly4.2. Thread dip tube (fig 2-B) into dip tube (fig 2-A) .4.3. Thread dip tubes (A + B) (fig 2) into pump (fig 1-1).4.4. Loosen joint nut (fig 1-6) and adjust the length of dip tube (fig 1-C) to fit the height of the drum and fix by re-tightening joint nut.4.5. Length of assembled dip tubes4.6. Dip tube (A + B + C) = 690mm - 980mm.4.7. Dip tubes (B + C) = 350mm - 640mmNote: Dip tube (C) is located within dip tube (B) and is extended by loosening joint nut (fig 1-6) and pulled out to required length.Re-tighten joint nut.4.8. To attach dip tube assembly (B + C)4.9. Unscrew dip tube (B) from dip tube (A), and unscrew dip tube (A) from the pump (fig 1-1) and retain.4.10. Thread dip tube assembly (B + C) into pump (fig 1-1).4.11. Delivery hose attachment4.12. Attach delivery hose (fig 1-4) to pump outlet and secure with spring hose clamp (fig1-5).TP6809 Issue 1 26/01/21Original Language Version© Jack Sealey LimitedRefer toinstructionsWear eyeprotectionWear protectiveglovesWear protectiveclothing

/ 2

Related manuals for Sealey ADBLUE TP6809