Sealey 4040A Series Quick Start Manual

4TONNE TROLLEY JACK WITH ROCKET LIFTMODEL NO: 4040A SERIESThank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to theseinstructions, and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY9 Ensure the jack is in sound condition and good working order. Take action for immediate repair orreplacement of damaged parts. Use genuine parts only. The use of improper parts may be dangerousand will invalidate the warranty.9 Locate the jack in a suitable, well lit working area.9 Keep working area clean and tidy and free from unrelated materials.9 Use jack on level and solid ground, preferably concrete.9 Avoid tarmacadam as jack may sink in. Chock wheels of vehicle.9 Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear(or “PARK” if automatic).9 Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allowfor vehicle tilting.9 Ensure all non-essential persons keep a safe distance whilst the jack is in use.9 Ensure there are no passengers in the vehicle.9 Place jack under only those lifting points recommended by vehicle manufacturer (see vehicle handbook).9 Check that the lifting point is stable and centred on the jack saddle.9 Ensure the jack wheels are free to move and that there are no obstructions.▲ DANGER: Use the jack for lifting only, NOT for supporting the lifted load.9 Ensure there are no persons or obstructions beneath the vehicle before lowering.9 Use suitable axle stands under the vehicle before proceeding with any task.9 Use a qualified person to lubricate and maintain the jack.9 Ensure that only hydraulic jack oil is used in the jack.8 DO NOT operate the jack if damaged.8 DO NOT allow untrained persons to operate the jack.8 DO NOT exceed the rated capacity of the jack.8 DO NOT allow the vehicle to move during lifting or lowering, or use the jack to move the vehicle.8 DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.8 DO NOT work under the vehicle until appropriately rated axle stands have been correctly positioned.8 DO NOT use the jack for purposes other than that for which it is intended.8 DO NOT top up hydraulic system with brake fluid. Use hydraulic jack oil only.8 DO NOT adjust the safety overload valve.9 When not in use store jack, fully lowered, in a safe, dry, childproof area.2. INTRODUCTIONSingle-piece hydraulic unit with heavy base design and large jacking saddle. Universal joint release mechanism allows safer, more controlledlowering of the jack. Rocket Lift feature brings lifting arm into contact with jacking point with minimal pumps. Polyurethane wheels forsmoother manoeuvrability and helps prevent damage to workshop floor. Magnetic wheel nut retention tray. Protective jack handle sleevehelps prevent accidental damage to car bodywork when pumping the handle. Range available in five different colours. 2 Year Guarantee -2nd year subject to T&Cs and registration on website (www.sealey.co.uk).3. SPECIFICATIONModel No: ...................................................... 4040A SERIESCapacity ...................................................................... 4tonneMinimum saddle height .............................................. 100mmMaximum saddle height ............................................. 533mmMaximum chassis height ............................................ 162mmLength ........................................................................ 751mmOptional rubber jack pad (not supplied) ......................... JP174. ASSEMBLY4.1. Insert the upper half of the handle into the lower half. It is retained in place by a spring pin. See Parts Diagram.Original Language Version© Jack Sealey LimitedRefer toinstructionsWear safetyfootwear4040AB, AG, AO, AR, AY Series Issue 3 (H, 3) 14/09/22

/ 2

Related manuals for Sealey 4040A Series