Menu
Sealey 3000LJ Instructions Manual
   |
Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts.Use genuine parts only. The use of non genuine parts may be dangerous and will invalidate the warranty. Locate the jack in a suitable, well lit working area. Keep working area clean and tidy and free from unrelated materials. Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as the jack may sink in. Place wedges under wheels of vehicle, but ensure the jack wheels are free to move and that there are no obstructions. Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if automatic). Ensure minimum distance of 0.5m between the vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting. Ensure there are no passengers in the vehicle and that all non-essential persons keep a safe distance whilst the jack is in use. Place the jack under lifting points recommended by the vehicle manufacturer (see vehicle hand book). Ensure lifting point is stable andcentred on the saddle. DANGER: Use the jack for lifting only, NOT for supporting the lifted load. Use suitable capacity axle stands under the vehicle before proceeding with any task. Ensure there are no persons or obstructions beneath the vehicle before lowering. DO NOT operate the jack if damaged. DO NOT work under the vehicle until axle stands have been correctly positioned. DO NOT exceed the rated capacity of the jack and DO NOT adjust the safety overload valve. DO NOT jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances. DO NOT allow the vehicle to move while supported by the jack, or use the jack to move the vehicle. DO NOT top up the hydraulic system with brake fluid. Use hydraulic jack oil only and use a qualified person to maintain jack hydraulicsystem. DO NOT allow untrained persons to operate the jack and DO NOT use jack for purposes other than for which it is designed. DO NOT allow persons to ride on the jack. When not in use store the jack, fully lowered, in a safe, dry, childproof area.InsTRUcTIons foR:3tonne TrOlley jack wiTh safeTy lOckMoDEL no: 3000ljYour new Jack is produced and manufactured to a high standard of dependability and will, if used according to these instructions and properlymaintained, give you years of trouble free performance.ImpORTANT: reaD These iNsTrucTiONs carefully. NOTe The safe OPeraTiONal reQuireMeNTs, warNiNGs aND cauTiONs.use This jack cOrrecTly aND wiTh care fOr The PurPOse fOr which iT is iNTeNDeD. failure TO DO sO May cause DaMaGeOr PersONal iNjury aND will iNvaliDaTe The warraNTy. reTaiN These iNsTrucTiONs fOr fuTure use.1. safeTy PrecauTiONs2. iNTrODucTiON & sPecificaTiONsModel No: . . . . . . . . . . . . . . . . . . . . . . . . . 3000ljcapacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 3TonneLocking Position 1: . . . . . . . . . . . . . . . . . . . 325mmLocking Position 2: . . . . . . . . . . . . . . . . . . . 405mmLocking Position 3: . . . . . . . . . . . . . . . . . . . 470mmMin. saddle height . . . . . . . . . . . . . . . . . . . 145mmMax. saddle height . . . . . . . . . . . . . . . . . . . 505mmMax. chassis height . . . . . . . . . . . . . . . . . . 190mmLength. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 690mmWeight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37kgOriginal Language Version 3000LJ Issue: 1 - 05/03/14steel framed 3tonne locking jacks with a three position safety locking mechanism that provides additional load security and hydraulic systemfail safe. Automatic bypass prevents jack damage from over pumping. for safety reasons always use in conjunction with axle stands in pairs.© Jack sealey Limited |
Related manuals for Sealey 3000LJ
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved