Sealey 1000ETJ Manual

1 TONNE VERTICAL TRANSMISSION JACKMODEL NO: 1000ETJThank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,and properly maintained, give you years of trouble free performance.IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USETHE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/ORPERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.1. SAFETY WARNING! Ensure all preliminary checks are carefully carried out before use of jack. Immediatelyrepair or replace damaged parts (use authorised service agent). Ensure use of genuine parts only.Unauthorised parts may be dangerous and will invalidate the warranty. WARNING! Use jack on level and solid ground (B), preferably concrete. Ensure the floor over whichthe jack will be transported is swept clean.▲ DANGER! DO NOT use on tarmacadam, or any other soft surface as jack may sink or topple. Seriousinjury may result if ignored.▲ DANGER! If jack tips or leans STOP WHAT YOUR ARE DOING. MOVE QUICKLY TO A SAFEDISTANCE. DO NOT TRY TO HOLD OR STEADY JACK.9 Use jack in a suitable work area. Keep the area clean and tidy and free from unrelated materials.9 Ensure there is adequate lighting.9 Before use ensure the gearbox weight and size does not exceed the capacity of the jack.9 Ensure the vehicle is raised and stabilised at the correct height before attempting to move the jackunder the vehicle.9 Ensure the jack saddle is fully lowered (A) and is clean, dry, and oil free before attempting to transportthe jack with or without a load.9 Keep all unauthorised persons away from the jack during lifting and lowering and when in transit.9 Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip safety shoes.9 Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery, and contain and/ortie back long hair. WARNING! Ensure that the load is placed level and centrally on the jack saddle (C) and that it is fixedin place before attempting to lift,lower or transport the load.9 The lowering speed will vary according to the weight of the load and the release valve setting.9 Diligence is required in ensuring that you continually monitor the operation until completed.9 Should the jack make any abnormal sounds during use, STOP IMMEDIATELY and contact your localservice agent.8 DO NOT operate the jack if any parts are damaged or missing.8 DO NOT exceed the rated capacity of the jack.8 DO NOT raise or lower vehicle lifting platform whilst the transmission jack is being used.8 DO NOT transport the jack with, or without a load, with the saddle in the raised position.8 DO NOT get the jack wet, or use it in damp or wet locations or areas where there iscondensation.8 DO NOT operate the jack when you are tired or under the influence of alcohol, drugs orintoxicating medication.8 DO NOT lift or support vehicles with the jack and DO NOT use the jack as a load-sustainingdevice.8 DO NOT use the jack for any purpose other than removal, transportation and the installation oftransmissions.8 DO NOT make any modifications to the jack.8 DO NOT adjust, or tamper with, the safety valve.8 DO NOT remove any labels from the jack. If the labels are damaged or unclear, replace them.8 DO NOT use brake fluid to top up the hydraulic unit. Use Sealey hydraulic oil only.9 Use a qualified person to lubricate and maintain the jack.9 Before storing the jack in a safe area, ensure that all parts are clean and free of grease and oil,especially the saddle.2. INTRODUCTIONManufactured to exacting standards and suitable for general workshop applications. Modelfeatures dead man’s handle for added safety and strong construction for durability. Thiseconomy hydraulic unit is slightly smaller than other models in the range. Can be fitted withAdjustable Gearbox Support - check specification in table.Refer toinstructionmanualWear safetyfootwearABC1000ETJ Issue 2 (ALL) 21/09/23Original Language Version© Jack Sealey Limited

/ 3

Related manuals for Sealey 1000ETJ