OneStart

Menu
Sanyo DVP-P1EX Technical Information Manual pdf 15 page image

Sanyo DVP-P1EX Technical Information

Also see for DVP-P1: Service manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 preview
Contents
  1. SERVICE TOOLS
  2. AN OVERVIEW OF THE MECHANISM
  3. Overview
  4. Paper Advance Drive
  5. Ink Ribbon Drive
  6. DISASSEMBLING THE MAIN PARTS OF THE MECHANISM
  7. S REEL ASSEMBLY
  8. HEAD
  9. PAPER EXIT ROLLER
  10. ASSY, MOTOR STEPPING
  11. PULLEY,DRUM
  12. CHASSIS,SUB LOWER
  13. SLIDE,LEVER TPH
  14. TROUBLESHOOTING
  15. Not printing
  16. Paper stopping
Sanyo DVP-P1EX Technical Information Manual pdf 15 page image
–15–ASSEMBLY NOTES:1. Install the “PULLEY,RELAY DRUM(4G200) ” and the“STOPPER, BELT DRUM(4G300) ” to the “ASSY, LE-VER, PULLEY(4G100) ” with the “SPECIAL WAHSER-3X0.5(4G400) ”.Turn the raised side of the “STOPPER,BELT DRUM(4G300) ” toward the “PULLEY, DRUM(4F000) ” asshown in Fig. B of Fig. 3-7-2.2. Insert portion A into hole 1 and initially install the “ASSY,LEVER, PULLEY(4G100) ” using the “SCR S-TPG BIN2.6X3(4N000) ” as shown in Fig. A of Fig. 3-7-2.3. Referring to Fig. 3-7-3, adjust the pressure welding valueand install the “ASSY,LEVER,PULLEY(4G100) ” asfollows:a. Hook the “BELT, DRUM(4I000) ” and the “BELT,MOTOR STEP(4J000) ” on the gears, and tighten the“SPECIAL SCREW-2.6X8(4H000) ” and the “SCR S-TPG BIN 2.6X3(4N000) ” at the point where both beltsstretch tightly.b. Rotating the “PULLEY, DRUM(4F000) ” clockwise,rotate the “BELT, DRUM(4I000) ” more than onerevolution.c. Set the Ruler (VJ8-0228) along the “BELT,DRUM(4I000) ”, and confirm that the pressure welding valueis [1.34N±0.29N] when pressing the Dial TensionGauge DTN-150G (VJ8-0226) until play in the“BELT,DRUM(4I000) ” is 1mm. The measuring posi-tion and the direction of pressure are shown in Fig. 3-7-1.d. If the pressure welding value is not [1.34N±0.29N],loosen the “SPECIAL SCREW-2.6X8(4H000) ” andfine-adjust the “ASSY,LEVER,PULLEY(4G100) ”,then re-tighten the “SPECIAL SCREW-2.6X8(4H000) ”. Repeat steps b and c above until thepressure welding value is within [1.34N±0.29N].e. Referring to section 3-6, adjust the tension of the“BELT,MOTOR STEP(4J000) ”.PULLEY,DRUM(4F000)PULLEY,RELAY DRUM(4G200)BELT,MOTORSTEP(4J000)ASSY,MOTORSTEPPING(4K000)BELT,DRUM(4I000)Bending value 1mmPosition of measuring tensionBendingvalue 0.5mmFig. 3-7-1SCR S-TPG BIN2.6X3(4N000)ASSY,LEVER,PULLEY(4G100)SPECIAL SCREW-2.6X8(4H000)PULLEY,RELAYDRUM(4G200)STOPPER,BELTDRUM(4G300)SPECIALWAHSER-3X0.5(4G400)SPECIALWAHSER-3X0.5(4G400) BELT,MOTORSTEP(4J000)BELT,DRUM(4I000)Fig. AFig. BHole 1Portion ASTOPPER,BELTDRUM(4G300)Turn the raised side towardthe “PULLEY,DRUM(4F000)”.Fig. 3-7-2Dial tension gaugeDTN-150G(VJ8-0226)Ruler(VJ8-0228)ASSY,LEVER,PULLEY(4G100)SPECIAL SCREW-2.6X8(4H000)BELT,DRUM(4I000)PULLEY,DRUM(4F000)Fig. 3-7-3
/ 30
Related manuals for Sanyo DVP-P1
Sanyo DVP-P1EX Instruction Manual first page preview
Sanyo DVP-P1EX Instruction Manual
Sanyo DVP-P1EX Instruction Manual first page preview
Sanyo DVP-P1EX Instruction Manual
Sanyo DVP-P1EX Instruction Manual first page preview
Sanyo DVP-P1EX Instruction Manual
Sanyo DVP-P1EX Service Manual first page preview
Sanyo DVP-P1EX Service Manual
This manual is suitable for:
DVP-P1DVP-P1CDVP-P1EX
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved