OneStart

Menu
Sanyo DMP-692 Instruction Manual Manual pdf 13 page image

Sanyo DMP-692 Instruction Manual

Page 1 previewPage 2 previewPage 3 previewPage 4 previewPage 5 previewPage 6 previewPage 7 previewPage 8 previewPage 9 previewPage 10 previewPage 11 previewPage 12 previewPage 13 previewPage 14 previewPage 15 previewPage 16 previewPage 17 previewPage 18 previewPage 19 previewPage 20 previewPage 21 previewPage 22 previewPage 23 previewPage 24 previewPage 25 previewPage 26 previewPage 27 previewPage 28 previewPage 29 previewPage 30 previewPage 31 previewPage 32 previewPage 33 previewPage 34 previewPage 35 preview
Contents
  1. Table Of Contents
  2. INTRODUCTION
  3. IMPORTANT SAFETY INSTRUCTIONS
  4. FCC INFORMATION
  5. PREPARATION FOR USE
  6. BATTERY BACK-UP SYSTEM
  7. using the ac adaptor
  8. LOCATION OF CONTROLS & INDICATORS
  9. REMOTE CONTROL
  10. OPERATING INSTRUCTIONS
  11. Daylight saving / standard time selection
  12. setting the clock
  13. RADIO OPERATION
  14. PRESETTING STATIONS IN THE TUNER MEMORY
  15. SLEEP TIMER
  16. ALARM SETTING
  17. iPod / iPhone OPERATION
  18. choosing the correct adaptor
  19. DOCK ADAPTOR COMPATIBILITY
  20. iPod / iPhone OPERATION CONTROLS
  21. TROUBLESHOOTING GUIDE
  22. TECHNICAL SPECIFICATION
  23. THE UNIT SUPPORTS THE LISTED iPods / iPhones
  24. WARRANTY
Sanyo DMP-692 Instruction Manual Manual pdf 13 page image
OPERATING INSTRUCTIONSCONNECTING EXTERNAL DEVICES12• Make sure that you have fully extended the FM antenna wire.• Be sure to connect the external AM Loop Antenna to the AM Antenna Jack on the backpanel if you are planning to listen to AM radio stations (refer to page 17 for connectioninformation) .• Make sure you have removed the mylar insulation tab from the remote control.• Make sure that the system is connected to an AC outlet that is always “live”.• Do not connect the system to an AC outlet controlled by a wall switch.General ControlsMost of the main functions of this system can be operated by the controls on the top panelof the main unit, or by the buttons on the remote control. If a specific function canonly be operated by the remote control, or by the top panel controls, this will be clearlyindicated in the instructions.When operating this system with the remote control, make sure that the IR (Infrared)transmitter on the front of the remote control is pointed at the remote sensor on the frontpanel of the main unit.The effective operating range of the remote control is approximately 20 feet. Please note thatbright sunlight or room lighting may interfere with the remote control operation. If the remotecontrol is not operating properly, try reducing the brightness of the room or moving closer tothe main unit. If this does not solve the problem, it may be time to change the remote controlbattery.Auxiliary Input JackThis system includes an AUX IN Jack to allow you to connect external audio equipmentand listen to the sound from the external equipment through the speakers of this system.To listen to the external audio source:• Connect the external audio equipment to AUX IN jack on the rear panel of the system asshown below. The connection cable is not included:Select the AUX mode by repeatedly touching the MODE buttonon the top panel or by repeatedly pressing the MODE button onthe remote control until the “AUX” indicator appears above thetime display.plugExternal audio sourceSignal cord (not included)
/ 35
Related manuals for Sanyo DMP-692
Sanyo DMP-P6 Instruction Manual first page preview
Sanyo DMP-P6 Instruction Manual
Sanyo DC-MX40i Instruction Manual first page preview
Sanyo DC-MX40i Instruction Manual
This manual is suitable for:
DMP-692
Product
Menu
Learn More
Menu
Legal
Menu
Copyright © 2024 OneStart. All Rights Reserved