Sanyo CE42LE1 Instruction Manual

Also see for CE42LE1: Instruction manual

Contents

Sanyo CE42LE1 Instruction Manual Manual pdf 7 page image

7Press the MENU button and select Sound using the e or dbuttons, press the 8 button to enter.Select and adjust to obtain the best sound settings for yourenvironment using the e , d and 7 8 buttons.Press the MENU to return to Main Menu. These settingsautomatically store when you exit the menu.Press the MENU buttonto exit menu.■ OSD LanguageUse the 7 or 8 buttons to select the prefered OSD language(French, German, Italian, Spanish, Dutch). Press the MENU but-ton to exit■ AV2 settingIn setting menu, to select AV2 press the d button and set to Y,Pb,Pror RGB, H/V depending on your external equipment.1. Press the MENU button. Select Setting using the e or d buttonpress the 8 button to enter.2. Select AV2 setting using the e or d button.3. Press the 7 or 8 button to select either Y,Pb,Pr or RGB H/V.4. Press the MENU button to exit, this automatically stores yourchanges.5. Press the MENU button to exit.■ Off-timer settingThe Off timer will switch the monitor into the standby mode when theselected time has elapsed.1. Press the MENU button. Select Setting using the e or d buttonpress the 8 button to enter.2. Select Timer using the e or d button, press 8 buttons to enter.3. Press the 7 or 8 button to change time.The time changes in 5 minute steps.The maximum time is 120 min-utes.If you have set the off timer, a display appears in the corner of thescreen when the recall button is pressed.✐ If the monitor is switched off by the standby button4 on theremote control or by the standby switch4 on the bottom of theLCD monitor the timer settings will be cancelled.Connect your PC to either PC-IN or RGBHV on the rear of the set.Once connected select PC mode or AV2 (RGBHV, see page 4 forAV2 input settings) via the v button on your remote control. Theset will become a monitor for the PC.By pressing the MENU button on the remote control a menu windowwill appear on screen, this allows the settings to be adjusted.To adjust the Picture settings select picture using the e or d buttonson the remote then the 8 button to enter the following picturesettings menu.Press the 7 or 8 buttons to adjusted the Picture brightness and thesame to adjust the contrast of the picture. Press the 8 button toenter sub menusPicture position changes the picture horizontally or vertically, this isdone by using the 7 or 8 buttons on the remote control.Video adjust changes the Phase and the clock of the screen. If thepicture is blurred or grainy this function will adjust it to a clearerpicture by using the 7 or 8 buttons on the remote control.Auto Adjust will automatically adjust the picture by using the 8button. This will change all the above settings automatically .Autoadjust can also be achieved by pressing the /recallbutton on the remote control without having to select the menuResolution displays the current resolution of the picture. This is forinformation only and cannot be adjusted.White tone: Using the 7 or 8 buttons it is possible to adjust thecolour tone of the picture using the White tone Red(R) / Green (G)/Blue(B). This will adjust the picture to show more or less of thechosen colour. For example if red is selected you can adjust the proportion of red in the picture to increase or decrease using the 7 or 8buttonsNative Resolution is used when the PC can output WXGA1366 x 768. The setting on your Monitor set can be changedto receive XGA/WXGA signal using the 7 or 8 buttons . Once thenative resolution has been selected, save the settings by switchingthe monitor off then on using the standby button.For Sound settings refere to previous menuSetting: select the menu button on your remote and using the e ord buttons to select Settings. The 8 button will enter the settingsmenu.Timer and AV2 settings are the same as in all other input modes(pg 7)Power save if turned ON will switch the monitor into Powersavemode after 1 minute if no signal is detected, the LED light will turn abrighter blue to indicate stand by. The monitor will automatically turnback on when a signal has been detected (PC input / RGBHV).Use 7 or 8 buttons to select power save ON or OFF.rDMENU OPERAMENU OPERATIONTION: Select : Adjust MENU : ExitSettingOSD Language EnglishTimerAV2 setting Y,Pb,Pr/RGB, H/VText Language Greek/ East/ West/ CyrillicSetting menuMENUTimerTIMER 5 ~ 120: Select : Adjust : ExitGB GBPC menu settingsMain MenuPicture: Select : Adjust MENU : ExitSettingSoundPicture: Select : Adjust MENU : BackBrightnessContrastPositionVideo AdjustAuto AdjustResolutionWhite Tone RWhite Tone GWhite Tone B1024 X 768 @60HzNative Resolution XGA / WXGA 1366 x 768: Select : Adjust MENU : ExitSettingOSD Language EnglishTimerAV2 setting Y,Pb,Pr/RGB, H/VPower save ON/ OFFSound menuSoundVolumeBalanceBassTreblePreset Personal / Talk / Music / NormalSurround OFF / Mid / Max: Select : Adjust MENU : Back