Samsung SH-D162D User Manual

Also see for SH-D162D: Manual User manual User guide User manual

3 4DVD-ROM DRIVESH-D162D(TS-H352D)BG68-01434A Rev.00- http://www.samsung-ODD.com- http://www.samsung-ODD.com5When using one EIDE cable• Connect the cable to the SL (Slave) of the Master/Slave Select Terminal at the rearof the DVD-ROM drive.When using two EIDE cable• Connect the cable to the MA (Master) of the Master/Slave Select Terminal at the rearof the DVD-ROM drive.- If there is only one Optical drive: select MA (Master).Hard DriveSlave Drive (Choose the SL Jumper)MainBoardHard DriveMaster Drive (Choose the MA Jumper)MainBoardSEC 1PRI 1SEC 1PRI 1-If there is two Optical drive, select MA (Master) / SL (Slave).Hard DriveMaster Drive (Choose the MA Jumper)Slave Drive (Choose the SL Jumper)MainBoard(Choose the MA Jumper) (Choose the SL Jumper)Emergency eject hole LEDDisc compartmentEject ButtonIf the compartment does not openwhen you press the Eject button,power off the computer, insert a pinor unfolded paper clip in the holeand push firmlhy)FrontRearSound output terminal Interface terminalDigital outputterminalMaster/slave select terminal Power terminalAccessoriesUser Guide, Screws.Design and specifications are subject to change without prior notice.Introduction• Design and specifications are subject to change without prior notice.Connecting the Cables to theDVD-ROMConnecting the CablesConnecting the power cable• The 4-pin power cable from the internal power unit of your computer mustbe connected to the power terminal the rear of the DVD-ROM drive.1Connecting the EIDE cable from a sound card•Connect the 4-pin audio cable between the sound output terminalDVD-ROM drive and the audio input terminal on the sound card.4Installing a jumper on the master/slave select termina•Connect a jumper to the rear side of theDVD-ROM.If the jumper is connected to MA (Master), it will work in the Master mode.If the jumper is connected to SL (Slave), it will work in the Slave mode.If the jumper is connected to CS (CSEL), you can control the device by using thhost interface signal CSEL. (In general, connection to MA is recommended.)2 Connecting the EIDE cable•Insert the EIDE cable (40-pin), which is connected to the harddisk to the interface terminal.(Place the red line of the cable close to the Pin 1.)3Power cableEIDE cableMaster/slave select terminalAudio cableCS : Cable Select(CSEL)SL : SlaveMA: Master6 7Installing the DriveInstalling the DVD-ROM DriveIf necessary, attach a horizontal bracketto both sides of the drive.• You can purchase these accessories separatelyfrom your computer dealer.(Screws for use: M3 X 6 X 4)1Remove the plate from a free expansion slot and install theDVD-ROM drive, as shown in the illustration.• If you have no free expansion slot, install the drive in place of thediskette drive.• Make sure to use the standardized screws supplied (M3X6).- To use screws other than M3X6 may result in malfunction.System RequirementsIntel Pentium II 350MHz(or higher), 128 MB of RAM (or higher) with an EIDE interface,Windows 2000/XP/Vista / Windows NT 4.0 (or higher)2How to install the DVD-ROM drive on your PC. First, remove the cover;connect the cable to the DVD-ROM drive and then to the PC.DVD-ROMDriveHorizontalBracketPlateUsing the Drive/Storing and CleaningYour DiscsPush the power button and boot the computer.1After booting the computer, open the disccompartment by pressing the Eject button.2Insert the disc (CD) with the label on the discfacing upwards and close the disc compartmentby pressing the Eject button. The indicator lightcomes on.3Play the disc (CD).4Using the DVD-ROM Drive• Do not place a disc in direct sunlight.• Store a disc vertically in a well-ventilated andstable location.• Do not write or attach a label on a disc.• Do not drop a disc or place heavy objects on it.• Do not touch the surfaceof a disc; hold it by theedges.• To clean a disc, polish lightlyfrom the inside of the disc to theoutside with a soft cotton cloth.Storing Your DiscsCleaning Your Discs• Run the CD player program supplied with the sound card or play theWindows Media Player.Playing CD-DA/Audio CDs• Follow the instructions provided with the disc.•A video card or MPEG software and a sound card need to be installed to view video CDs.Playing Video CDs• The disc may not function properly if there are fingerprints, foreign substances ordust on the disc surface.• If the drive is vertically installed, you cannot use an 8 cm Mini Discbecause the disc is movable.8 9Solving Technical ProblemsThe DVD-ROM drive is notdetected by the computer.After installing the DVD-ROMdrive, the PC gets slower.• Check that the power, audio and EIDE cables are correctlyconnected to the computer.• Change the EIDE cable and reconnect it to the computer.Preferably, connect a second EIDE cable to the DVD-ROMdrive in master mode.• Check the position of the jumper in the master/slave selectterminal.The DVD-ROM drive is notrecognized by MS-DOS.• Reinstall the device driver or update it with the latest versionby downloading it from the Samsung Web site.- http:// www.samsung-ODD.com- http:// www.samsung.comThe DVD-ROM drive is notdetected by Windows.• This case may occur when there is a Windows installationproblem; reinstall Windows.When the MPEG softwareplays a Video CD, the picturesare not regular and the runningspeed is too slow.• Adjust the size of the replay screen.• After checking the display resolution, adjust it, if necessary.A CD is not read or is readtoo slowly.• Check whether the CD is of good quality and clean it,if necessary.The disc compartment willnot open.• Check that the power cable is correctly connected.• Power off and disconnect the PC.Insert a pin or unfolded paper clip in the emergency hole and pushfirmly until the disc compartment opens.The DVD-ROM drive is notdetected after it is connectedto a sound card.• The interface mode of the sound card is AT-BUS.You must therefore connect the DVD-ROM drive to the EIDEport on the PC mother board, rather than to the sound card,or install an EIDE compatible sound card.The Disc is not in message isdisplayed even though a dischas been inserted.• The computer may not recognize the disc if you start playbacktoo quickly after inserting the disc.Open and close the disc compartment and try again.• Clean the disc and try again.• The friction noise generated during SPIN-UP and STOP is caused by theAutomatic Ball Balancing System(ABS) and is not a malfunction.Technical SpecificationsSH-D162D(TS-H352D)SECTIONSDISCDRIVEPERFORMANCEFRONT PANELREAR PANELGENERALERROR RATEOPERATINGENVIRONMENTDisc types supportedDisc diameterData transfer rateSustainedPIO mode 4Access time(RANDOM)Data Buffer capacitySlide mechanismSpindle motorLoad mechanismEject buttonRequired powerInterface connectorAudio outputIndicator(LED)CD-DA(Audio), CD-ROM, CD-R, CD-RW, Photo-CD(Single, Multi-session), Video CD ready, Enhanced CD, CD-I/FMV,CD-TEXT,CD-Plus, DVD-ROM, DVD-VIDEO, DVD+R, DVD-R,DVD+RW, DVD-RW, DVD-RAM, DVD+R/-R Dual120mm or 80mmMax. 21,600KB/sec(16X)16.6MB/secDMA mode 2UDMA mode 216.6MB/sec33.3MB/secMax. 7,200KB/sec (48X)CD DVD110ms (typical)198KBLaser Semiconductor laserStepping motorBrushless Sensorless DC motorTray. DC motor (Soft Eject). Horizontal/Vertical.10 -15 Mode 1:10 -12, Mode 2:10 -9Eject, Insert1.5A (rms)ATAPILine out 0.7V ± 20% : 47kΩBUSYJumper blockOperationsMolex 70203 or other compatible modelsTemperature: 5~45°C Humidity: 10~80%Storage Temperature: -25~60°C Humidity: 10~90%Dimensions 148.2 (W) x 42 (H) x 170 (D) mm (including bezel)Net weight 740 gUser Guide - ENGLISHFCC ComplianceThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference in aresidential installation.This equipment generates, uses, and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in a particularinstallation. If this equipment does cause harmful interference to radio or television reception,which can bedeter-mined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:• Re-orient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This marking shown on the product or its literature,indicates that it should not be disposed withother household wastes at the end of its working life.To prevent possible harm to theenvironment or human health from uncontrolled waste disposal,please separate this from othertypes of wastes and recycle it responsibly to promote the sustainable reuse of material resources.Household users should contact either the retailer where they purchased this product,or theirlocal government office,for details of where and how they can take this item for environmentallysafe recycling.Business users should contact their supplier and check the terms and conditions of the purchasecontract.This product should not be mixed with other commercial wastes for disposal.CAUTIONChange or modifications not expressly approved by the manufacturer responsible forcompliance could void the user ’s authority to operate the equipment.LASER STANDARDIEC 60825-1 :1993 +A1 :1997 +A2 :2001WEEECorrect Disposal of This Product (Waste Electrical &Electronic Equipment)(Applicable in the European Union and other European countries with separate collection systems)• Samsung Eco-markThe Samsung’s own Eco mark helps consumers to easily understand thatSamsung develops eco-friendly products. This mark represents Samsung’scontinuous effort to develop eco-friendly products.• RoHS(Restriction of the use of certain hazardous substances in electrical and electronic equipment)The RoHS, the environment regulation announced by European Union, restricts the use oflead, mercury, cadmium, hexavalent chromium, PBB, and PBDE in products put on themarket in The European Union after July 1, 2006.Safety PrecautionsThe following are basic precautions to ensure user safetyand reduce the risk of property damage.1 2Place the drive on a levelsurface.• Do not place the drive indirect sunlight.• Avoid low- or high-temperatureenvironments.• Avoid high-humidity environments.Handle with caution to preventdamage from external shock.Do not drop the drive, andprotect it fromsevere shocks.• It can damage the drive or causeit to malfunction.Do not move the drive while in operation anddo not attempt to open the disc tray byforce.Make sure to close all working programs beforeattempting to open the tray and always use theopen/close button.Do not use cracked, distorted ordamaged discs.Do not insert a pin into the emergencyopening while in operation.In particular, a disc with a crack on theinner tracks may break while in use.• Never allow food particles orforeign substances to enter thedrive casing.• To protect against the risk offire, do ot spill such liquids asalcohol and benzene on thedrive.Do not disassemble, attempt to repairor modify the device without expressapproval as directed in the manual.• To reduce the risk of damage,electric shock, and fire.Important to read and understandat all times Do not disassemble1. Check to see that the disc does not have a crack before use. If the disc has a crack (especially around the center hole), it is recommended thatyou make a copy immediately and use the copy instead. When a cracked disc is used continuously,the size of the crack is likely to grow and itwill eventually result in irreparable damage to the disc.2. Do not use low quality discs (i.e., illegal products, scratched or damaged discs).• Any change or modification not expressly approved by designated qualified personnel couldvoid your authority to operate this device.Warning/CautionWarning: To warn the user that failure to comply with the instructions may result inserious injury or death.Caution: To caution the user that failure to comply with the instructions may result indamage to property.• Failure to do so may cause thedevice to fall onto a hard surface,resulting in damage or malfunction.• If the power cable is not connectedproperly, it may cause a fire ordamage the drive. Check the directionof the power connector and the driveincline before connection.+5V DCGroundGround+12V DCWhen you install the driveWhile operatingOtherSH-D162D(TS-H352D)ENG/RUS 2007.5.30 11:55 AM Page 1All manuals and user guides at all-guides.comall-guides.com

/ 2

Related manuals for Samsung SH-D162D