| 
6 7EnglishPlease consult the following table BEFORE contacting your dealer or local SAMSUNGrepresentative.Changing the Drive and Driver SettingsResolving Technical ProblemsParameter Details/D: Specifies the name of the top DVD-ROM drive. The fieldmust contain the same information as specified by parameter in yourCONFIG.SYS file (which loads the corresponding DVD-ROM drive).*The MSCDEX command must have at least one /D parameter.If you add another DVD-ROM device, you must add and specifya corresponding /D parameter for each new drive./E If the EMS memory mode (Expanded Memory Support) isenabled, this parameter specifies that the DVD-ROM drivercan save sector buffers using EMS memory./K Specifies that MS-DOS can recognize a DVD-ROM volumewritten in kanji (Chinese characters). Must be used for allDVD-ROM volumes written in kanji./S Permits the DVD-ROM drive to be shared on the MS-NET orWindows for Work Groups server./V: When MSCDEX.EXE is loaded, this parameter indicates thememory status./L: Specifies the letter of the top DVD-ROM drive. If more thanone DVD-ROM drive is connected, the system automaticallyassigns arbitrary drive names to the additional drives./M: Specifies the number of sector buffers.Your DVD-ROM drive is controlled by:u MSCDEX.EXE (a Microsoft CD-ROM extensions program)u SSCDROM.SYS (the CD/DVD-ROM device driver)MSCDEX.EXE ParametersThe MSCDEX.EXE parameters are added to your AUTOEXEC.BAT file. Below is the syntax for eachparameter. Information indicated within square brackets [ ] is optional.\\MSCDEX.EXE [/E/K/S/V] /D: [/L:] [/M:]Example : The default set-up procedure adds the following default settings to your AUTOEXEC.BAT file:C:\SAMSUNG\MSCDEX.EXE /D:SSCD000SSCDROM.SYS ParametersThe SSCDROM.SYS parameters are added to your CONFIG.SYS file. Below is the syntax for eachparameter. Information indicated within square brackets [ ] is optional.DEVICE=\\SSCDROM.SYS /D: name> [P:]Example : The default set-up procedure adds the following default settings to your CONFIG.SYS file:Device=C:\SAMSUNG\SSCDROM.SYS /D:SSCD000 /P:1F0,14,1Details for each parameter are listed below.Parameter Details/P: Specifies the port for the interface card.Possible values: 1F0, 170Default: 1F0.Problem Meaning/SolutionThe softwareinstallation failedu Check that your hard disk is not full.u The installation floppy disk may be corrupted.Repeat the installation with the backup floppy disk.I re-booted my PCand it pausedduring the start-upprogram.After installing the device driver, your system start-up programmay take more time than expected. If it does not start-up after60 seconds, verify your AUTOEXEC.BAT file and, if necessary,contact your local computer dealer.The disc tray doesnot open.The drive may not be installed correctly.Verify the physical installation.I installed thesoftware and re-booted my PC. TheDVD-ROM driveicon/directory stilldoes not appear.u Verify the connections between the drive and your PC.Check that the 40-pin flat cable is connected to an IDEinterface (some PCs are equipped with an SCSI diskinterface).u Verify your AUTOEXEC.BAT file. Go to page 6 for theverification procedure.u Check the LASTDRIVE= command in the CONFIG.SYS file.The specified letter must take the DVD-ROM volume intoaccount. If you do not know which letter is assigned to theDVD-ROM, enter Z.u Using the documentation provided with your PC, check thatthe IDE hard disk is set up in MASTER mode.In the FileManager, theDVD-ROM icondoes not display.If you have installed the DVD-ROM drive... Then...And the software Re-boot your PC.And have not installed the software Install the softwarefollowing the instructionson page 5./D:] Refer to README. DOC.Changes the name for the DVD-ROM drive. Up to eightcharacters can be input.Default: SSCD000.Details for each parameter are listed below.SDR(Eng) 11/12/98 8:11 AM Page 4 |
