Samsung SC152C User Manual

Also see for SC-152: User guide User guide User manual User manual

1Front View of the CD-ROM Drive2System RequirementsRear View of the CD-ROM Drive34 5 6 7112 3 4 5 6Headphone ConnectorThe sound output terminal enables you to plug stereo headphones into the drive.It requires a 3.6 mm stereo mini-jack.112 3 4 5Digital output terminalYou can connect a sound card or MPEG card which support Digital outputterminal to your drive using this two-pin terminal.1 Turn OFF your computer. Remember to verify theconfiguration jumper on the rear of the CD-ROM drive.2 Remove the cover of your PC(main unit of the computer)3 Remove the blank cover panel of the 5.25 inch unit inwhich the CD-ROM drive is to be installed.6 Put the cover back on your PC.5 Install the CD-ROM drive into the unit and secure it withmounting screws (recommended standard M3x6x4)☛ Depending on your PC model, you may need toattach guide rails to the drive, so that the drive isheld firmly in place.☛ If you use screws that are longer than therecommended standard, you may damage thedrive.Before you install the CD-ROM drive, we strongly recommend that you make certainthat your set-up meets the system requirements listed below.Installing the CD-ROM DriveInstall the CD-ROM drive in your computer horizontally, making sure that the Open/Closebutton is on the right.To install the drive, proceed as follows.2 Sound output terminalYou can connect a sound card to your drive using this four-pin terminal.☛ This function is not covered in detail in this guide. Refer to the documentationsupplied with your sound card.3 Master/slave select terminalUsually, this is a pre-set configuration as illustrated below.☛ Verify that the setting is as illustrated. If it is not, simply remove the jumperand place it in the correct position.4 Interface terminalThis input/output interface terminal is used to connect the 40-pin flat cable fromthe IDE interface to the CD-ROM drive.5 Power terminalThe power terminal is a four-conductor male plug.Eject Button4 Disc compartmentThe compartment opens and closes automatically when you pressthe Eject button.Emergency eject holeIf the compartment does not open when you press the Eject button, power offthe computer, insert a pin or unfolded paper clip in the hole and push firmlhy)6 Eject Button5 Emergency eject holeIf the compartment does not open when you press the Eject button, power offthe computer, insert a pin or unfolded paper clip in the hole and push firmlhy)2 Headphone volume controlThis headphone volume control adjusts the volume for your headphones. You can onlyuse the headphone jack and volume control when you have installed the requiredsoftware utilities. For example, the Microsoft Windows Media player can be used.3 LED4 Connect the CD-ROM drive to the IDE interface and powercables Iocated inside your computer.☛ Connectors are keyed so it is impossible to put them inan incorrect position. Do not force the connectors, if theydo not seem to fit.ItemWindows versionMS-DOS versionDisk spaceFree expansion unitType of computerDescriptionWindows 95/98/2000/ME/XPWindows NT 4.0(or higher)5.0(or higher)100KB minimum5.25 inchIBM 486SX 20MHz (or higher) with an IDEinterface(or a 100% IBM-compatible computer)C D - R O M D R I V ES C - 1 5 2User's Guide - ENGLISHTechnical SpecificationsMax. 7800KB/sSC-152NSECTIONSDISCDRIVE PER -F O R M A N C EF R O N TPANELREAR PANELOPERATINGENVIRONMENTGENERALRELIABILITYERROR RATEDisc types supportedDisc diameterData transfer rateAccess time (1/3 stroke)Data buffer capacityLaserSlide mechanismSpindle motorLoad mechanismButtonIndicator(LED)Headphone outputVolume controlRequired powerInterface connectorAudio outputJumper blockWork areaStorage areaDimensions (W x H x D)Net weightMTBFCD-DA, CD-ROM Mode-1, CD-ROM XA Mode-2 Form-1, Form-2,CD-Plus, CD-Extra, Photo-CD(Single, Multi-session),Video CD ready, Enhanced CD, CD-I/Fmv, CD-R/RW120mm or 80mmPIO Mode - 4. DMA MW2, Ultra DMA(option)75ms(typical)128KBSemiconductor LaserGear motorBrushless motorTray, DC motor(Soft Eject)Mode-1 : 1block / 10 bits, Mode-2 : 1 block/10 bitsEject(Open/Close)BusyStereo Mini - jack (Ø 3,6 mm) 0.60 ± 20% (Vrms) 33ΩDial type+5V DC 1.3A, +12V DC 1.5AATAPILine out 0.70 ± 20%(Vrms), 47kΩDevice configuration jumperTemperature : 5~45 °C, Humidity : 8~80%Temperature : -40~60 °C, Humidity : 5~90%900g (set only)125,000 POH(Duty 20%)146mm(W) x 44.5mm(H) x 202(D)mmSAMSUNG continually strives to improve its products.Both the design specifications and these user instructions are thus subject tochange without notice.12 9BG68-00326A Ver : 03Safety PrecautionsThe following diagrams illustrate the precautions to be taken when usingyour CD-ROM drive.Setting Up the Device DriverIt is not necessary to set up additional device driver for Window95/98/2000/NT because it uses the device driver provided by the Window.Solving Technical Problems☛ Frictional sound detected during the operation of Spin-Up and Stop is made ABS(Auto Balance System), not by malfunction. Automatic Setup Manual SetupLAST DRIVE = Z- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -DEVICE = C :\SAMSUNG\SSCDROM.SYS /D : SSCD000 /V- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -C :\SAMSUNG\MSCDEX /D:SSCD0001 Insert the setup diskette in the diskette drive and change the directory to A:,where A: is the diskette drive.To do so, type A: after the C:\ prompt and press [Enter].2 Type CDSETUP and press [Enter].3 Reboot the computer.1 Make the C:\SAMSUNG directory.2 Copy the files from the diskette to the C:\SAMSUNG directory.To do so, type COPY A:*.* C:\SAMSUNG after the C:\ prompt and press[Enter].3 Edit the CONFIG.SYS file.Add the DEVICE=C:\SAMSUNG\SSCDROM.SYS \D:SSCD000 /V entry.4 Edit the AUTOEXEC.BAT file.Add the C:\SAMSUNG\MSCDEX /D:SSCD000 entry.5 Reboot the computer.You must not use the drive in any manner other than that specified in this guide.Avoid exposing your eyes or skin to direct or scattered radiation.CAUTION Do not attempt to repair the CD-ROM drive yourself. Contactyour dealer or local SAMSUNG representative for all repairs.If you make any adjustments or perform any operations otherthan those specified in this guide, you run the risk of exposure tohazardous radiation.WARRANTY Please refer to the Samsung limited warranty statements.Precautions 1. To reduce the risk of fire or electric shock, do not exposethis appliance to rain or moisture.2. Always check each disc for cracks before using it. If there arecracks on the surfaces, especially around the border of thecenter hole, we recommend that you make a copy of the discimmediately and then stop using it. If you continue using thedisc, it will probably develop more cracks and eventually causeirreparable damage.3. Do not use poor quality discs: From unknown sources Without any copyright Scratched or damaged in any wayProblem Meaning / SolutionThe CD-ROM drive is notdetected by the computer. Check that the power, audio and IDE cables arecorrectly connected to the computer. Change the IDE cable and reconnect it to the computer.Preferably, connect a second IDE cable to the CD-ROMdrive in master mode; see page 7 for further details. Check the position of the jumper in the master/slaveselect terminal. Reinstall the device driver or update it with the latestversion by downloading it from the Samsung Web site. This case may occur when there is a Windowsinstallation problem; reinstall Windows. Check whether the audio cable is correctly connectedto the sound output terminal on the CD-ROM drive andthe sound card CD-IN terminal. Check that the sound card is operational. Adjust the volume control. Install the latest version of the device driver. Check whether the CD is of good quality and clean it,if necessary. Check that the power cable is correctly connected. Power off and disconnect the PC. Insert a pin orunfolded paper clip in the emergency hole and pushfirmly until the disc compartment opens. Adjust the size of the replay screen. After checking the display resolution, adjust it, ifnecessary. The computer may not recognize the disc if you startplayback too quickly after inserting the disc.Open and close the disc compartment and try again. Clean the disc and try again. The interface mode of the sound card is AT-BUS.You must therefore connect the CD-ROM drive to theIDE port on the PC mother board, rather than to thesound card, or install an IDE-compatible sound card.After installing the CD-ROMdrive, the PC gets slower.The CD-ROM drive is notrecognized by MS-DOS.The CD-ROM drive is notdetected by Windows.No sound is heard from anaudio CD.A CD is not read or is read tooslowly.The disc compartment will notopen.When the MPEG software plays aVideo CD, the pictures are not regularand the running speed is too slow.The Disc is not in message isdisplayed even though a dischas been inserted.The CD-ROM drive is notdetected after it is connectedto a sound card.* The design of this product can be more or less changed according to itscharacteristics.FCC ComplianceThis equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmfulinterference in a residential installation.This equipment generates, uses, and can radiate radio frequency energy and,if not installed and used in accordance with the instructions, may causeharmful interference to radio communications. However, there is no guaranteethat interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can bedeter-mined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures:• Re-orient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.✱ Changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment

/ 2

Related manuals for Samsung SC-152