Menu
Saeyang MINI CRO Manual
  |
1) Connect the DC plug to the adaptor connector of control box.4-1. Battery chargingPower on/off & speed control KnobCharge display LEDSpeed display LED White >> Sky Blue >> Blue >> PinkPause buttonForward/Reverse switchHandpiece connectorFront panelControl boxHandpieceHandpiece standControl box stand (optional)AdaptorClip(optional)Handpiece holder (optional)Max speed : 30,000 RPMRun-timeCharging time : 3 hrs.Speed controlForward / Reverse rotationOverload protectionUse with the standard bitThe battery is a Li-ion rechargeable battery(consumable goods)Battery lifetime is limited and depends on working conditions.Please dispose used batteries in accordance with the national and local laws.Install the unit at your workplace and do not use in a dirty or very hot and humidenvironment.(-20~ 40, 0-90% RH)Please take care not to drop the handpiece or drill unit. This will result in damageto ball bearing and will affect the durability of the motor.Please do not allow water or other liquids to spill onto and into all units.After replacing a bur, please make sure to close the chuck handle.Do not open the chuck handle while the handpiece is in operation.While the handpiece is not in operation, it is recommended to leave a drill bit (bur)inserted into the chuck after cleaningMINI cro is a professional use only device, for use by professionals only.1. Precaution2. Features3. Part introductionPlease be sure to read this manual before operation.Portable control box & Micro-motor20,000 RPM30,000 RPM30,000 RPM9hrs10hrs, 4hrs6hrsSDE-MH20(30K), SDE-SH300SDE-MH20SDE-H200② ③ ④ ⑥ ⑦⑤Clip Type(Optional)Standard typeBack viewSide viewFront viewmade in korea4. Installation & OperationSee No.6 Safety protection system.Check the chuck and close the chuck.Check the motor and repair if themotor has a problemReplace the motor cord.Replace the carbon brushes.Correctly plug the motor cord to themotor connector of control box.Worn carbon brushes.In case any malfunction is found, consult with an official dealer.Trouble in the motor part.Defect in the motor cord.Motor stops suddenlywhile in use.Although a controlbox is fully charged,a handpiece fails torun.Loose connection of amotor cord with the motorconnector of control box.(1) To remove a bur, please turn a chuck handle clockwise until it clicks to stop, andthen pull out the bur.(2) To insert the bur, please turn the chuck handle counterclockwise until it clicks tostop.(3) Please be sure not to use bent, asymmetrical or damaged burs. Always use stand-ard burs.5. Bur(Bit) insertion and removal4-3. Pause Funtion1) If you press the Pause button during handpiece operation, the operationof the handpiece is temporarily stopped.2) Press the Pause button again to start the handpiece operation.1) Connect the handpiece to a control box.2) Turn the power on / off & speed control knob to the right SPEED LED turnswhite and power is on.3) Turn the Power on/off & speed control knob to the left or right to use theminimum and maximum rpm.4) Forward / Reverse can be selected using Forward / Reverse switch4-2. Operation by HandTo prevent from overheating, please be sure to separate the adaptor from thecontrol box. Also,please avoid operating the unit during charging hours.When charging, please make sure to use the original charge adapter andpower cord.2) The CHG LED lights up RED while the battery is charging, and the CHG LEDlights up GREEN when charging is complete6-1. Overload protection function: During overload, the speed display LED turns red and flashes, and the currentis cut off. Turn the knob to the left to turn off the power or press the pausebutton, release the cause of the overload, then turn the power on or releasethe pause to use again.6. Safety protection systemOverloaded or a chuck is open iin operation.(low speed) (high speed)made in koreaWarning about battery usage |
Related manuals for Saeyang MINI CRO
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved