Menu
Rain Bird IQNCCRS Installation And Configuration Manual
Also see for IQNCCRS: Manual
 |
Auto ConfigureMaster ValvesSensorsFloManagerFloWatchEdit Configuration and Stations...Direct Satelitte TasksSelect One or More Sites...Site Name Out of Sync Satellite Changes Alarm Satellites Off Auto Contacts...Add Site...SynchronizeEdit Site...Retrieve Logs...Site Name DescriptionTime ZonePostal Code(UTC-8:00) Pacific Time (US and Canada)Site 01OK CancelSatellitesProgram...Dry Run...Manual Operations...Configure...Add...Auto ConfigureMaster ValvesSensorsFloManagerFloWatchEdit Configuration and Stations...Direct Satelitte TasksClient SatelliteLXMEClient SatelliteServer Satellite20 gal/min11Satellite Name:Type:Connection Type:Server:Network Address:Description:Dry Run Warning for Max Flow:Max. Satellite Irrigation SimulStations:Max. Satellite Non-Irrigation SimulStations:PIN-Codes:Weather Source:Configuration StationsOK CancelUnprotectedDetect Modules automatically and update IQUpload Satelitte Configuration into IQUpload Satelitte Programming into IQRetrieve Learned Flow Data into IQOK CancelModulesConfigurationProgramsLearned Flow1. Choose Satellite 2. Choose IQNet TypeLXD DirectLXMEServerChoose the IQNet Server for this Client:Server SatelliteLXMEFLXMClientOK CancelAuto ConfigureMaster ValvesSensorsFloManagerFloWatchEdit Configuration and Stations...Direct Satelitte TasksSatellite 001LXMEIP Connection10.84.177.1650050 gal/min11Satellite Name:Type:Connection Type:Phone Number / IP AddressPort:Description:Dry Run Warning for Max Flow:Max. Satellite Irrigation SimulStations:Max. Satellite Non-Irrigation SimulStations:PIN-Codes:Weather Source:Configuration StationsOK CancelUnprotectedSatellitesProgram...Dry Run...Manual Operations...Configure...Add...1. Choose Satellite 2. Choose IQNet TypeLXD DirectLXMEServerLXMEFLXMClientOK Cancel1 IQNet Server/Client Communication • Connection Module (CM) PE-Cable and/or Radio Secondary CommunicationIQNet Server/ClientCommunication OverviewAllows a single Server Satellite with IQ pri-mary communication connection (Cellu-lar, Ethernet, etc.) to be shared with up to255 Client Satellites via Radio and/or Con-nection Module (CM) PE-Cable secondarycommunication.a. Utilizes lower cost IQNCCRS RS-232Cartridges for Client Satellites.b. Reduces yearly reoccurring com-munication costs for systems usingCellular communication.c. Provides Normally Closed MasterValve or Pump Start sharing be-tween Server and Client Satellites.d. Provides Weather Sensor (not FlowSensor) sharing between Serverand Client Satellites.Rain+Birdt IQNCCRS RS-232 Network Communication Cartridge -IQNet Server/Client Installation & IQ-Cloud ConfigurationFor Additional InformationSee IQ-NCC Cartridge Installationand Operations Guide for IQ3G-USA Cellular and IQNCCENEthernet Cartridge Installationand Configuration Instructions.Go to www.RainBird.com/for training, presentations,product literature andinformation for IQ-Enterprise and IQ-Desktop.IQ-Cloud Support(800) 254-0692IQCloudSupport@RainBird.comwww.RainBird.com/IQRain Bird Global Service Plan (GSP)(866) 477-9778www.GSPSupport@RainBird.com9 Go to www.rainbird.com/iqA New users: Select IQ-Cloud Sign-up.B Existing users: Select IQ-Cloud Login.10 Select Add Site13 Add Client SatellitesA Choose ESP-LX Controller Type.B Select Client IQNet Type.14 Configure Client SatellitesA Select Edit Configuration and Stations.B Enter the unique IQNet Network Address (2 to 56) that you selected in theSetup Wizard for each Client Satellite.15 Reverse Sync Data from each SatelliteA Select Auto Configure.B Check All Options.2018 Rain Bird CorporationtRegistered trademark of Rain Bird CorporationP/N: 690656-01 Rev. 6/18 D412613 Attach IQ Cables to Cartridges in Server andClient SatellitesC Select theServer Satellitethis Client isconnected to.12 Configure Server SatelliteA Select Edit Configuration and Stations.B Select IP Connection Type, enter the IP Address and Port Number for IQ-Cloudto communicate to the Server Satellite.11 Add Server SatelliteA Choose ESP-LX Controller Type.B Select Server IQNet Type.2 Install IQ-NCC Cartridges 4 Attach IQ Cables to Radio/CM ModuleAttach Supplied Y-Cable to Radios or Straight-Cable to CM Modules8 Check IQNet Satellite Communication Status fromthe Client Satellites7 Test Satellite Communication from theServer SatelliteB The Setup - Satellite Typescreen is displayed. Use +or - to select Direct' pressNext. NOTE: The IQ Port statuswill allways show Disabled forClient Satellites.g Turn the controller dial toETM/IQ Settings5 Setup Wizard for Server Satelliteg Turn the controller dial toETM/IQ Settings6 Setup Wizard for Client Satelliteg Turn the controller dial toETM/IQ SettingsB The Setup - Satellite Type screen isdisplayed. Use + or - to select Client;press Next.C The Setup – Satellite Address screenis displayed. Use + or - to select aunique address from 002-256 forthis satellite (press and HOLD but-tons to accelerate settings); pressNext.D The Setup – Satellite RadioPort screen is displayed. Use +or - to select a radio port op-tion (No Radio Installed, RadioInstalled); press Next.E The Setup – Satellite CM Portscreen is displayed. Use + or -to select a CM Port option (NoModule, Module Installed);press Next.F The Setup – CM PortTermination screen is dis-played. Use + or - to select aCM Port Termination option(On or Off ). NOTE: CM Porttermination is onlyrequired if this satellite isat the end of an IQNet PECommunication Cable path.If you are not sure, consultwith the system designer.A The IQ Settings main menu isdisplayed. Use the UP or DOWNarrows to select Setup Wizard;press Next.B The Setup - Satellite Typescreen is displayed. Use + or -to select Server; press Next.C The Setup – Satellite Addressscreen is displayed. ServerSatellites always have an ad-dress of 001; press Next.D The Setup – Satellite IQ Portscreen is displayed; press Next.E The Setup – Satellite RadioPort screen is displayed. Use +or - to select a radio port op-tion (No Radio Installed, RadioInstalled); press Next.F The Setup – Satellite CM Portscreen is displayed. Use + or- to select a CM Port option(No Module Installed, ModuleInstalled); press Next.g Turn the controller dial toETM/IQ SettingsA The IQ Settings main menu is dis-played. Use the UP or DOWN ar-rows to select Status; press Next.B The Satellite Status screen isdisplayed. Current status of IQ,Radio, and CM ports are shown.Press Signal to display 3G signalstrength.C The Signal Strength is displayed.The signal strength between thesatellite and the 3G Cellular net-work is indicated on a scale of1-10.D The Satellite Status screen is dis-played. Current status of IQ, Radio,and CM ports are shown. PressPing to check the communicationstatus with selected Clients.E The IQNet Ping screen is displayed.Use the + and - buttons to selectany Client address. Press Ping tocheck the communication status.The LCD will display Response-Yesif the ping is successful, or No foran unsuccessful ping.A The IQ Settings main menu is dis-played. Use the UP or DOWN arrowsto select Setup Wizard; press Next.A The IQ Settings main menu is dis-played. Use the UP or DOWN arrowsto select Status; press Next.Install IQ3G-USA Cellular orIQNCCEN Ethernet Cartridgein Server SatelliteInstall IQNCCRS RS-232 Cartridgesin the Client Satellites NOTE: Refer to IQ3G-USA Cellular andIQNCCEN Ethernet Cartridge InstallationPosters for full Installation instructions. NOTE: Use Y-Cable for satellites thathave both a CM Module and Radio.What’s NewIQ-Cloud Sign Up IQ-Cloud Login ENIQ-Cloud Support (800) 254-0692 | iqcloudsupport@rainbird.comIQ-Cloud LoginLoginConfigure this computerRain Bird IQ Central Control SystemTMUser NamePasswordI forgot my passwordLog On CancelWhat’s NewShow Quick StartC Select Configure this computerfor first time IQ-Cloud connectionon a new computer.D Enter User Name & Password toLogon to IQ-Cloud.3G CellularAntennaBackplaneConnect DB9 Cableend to Radio portConnect 2-pin cableend to CM ModuleESP-LX ControllerServer SatelliteIQ3G-USA orIQNCCEN CartridgeSupplied IQ-Y and Straight CablesConnect Cartridges to CM's and RadiosIQFSCMLXME Flow Smart Connection Modulesfor ESP-LXME Controllers and IQCMLXDConnection Modules for LXD ControllersTo Internetand IQ-CloudTo AdditionalConnectionModule ClientSatellitesTo AdditionalRadio orConnectionModule ClientSatellitesIQNCCRS CartridgeESP-LX ControllerESP-LX ControllerIQNCCRS Cartridge19-Gauge PECable, Twisted Pair,Shielded, Gel FilledCommunicationCable (Max 18K feet)IQSSRADIO or RB-SS-TN9B Radios(separate antennaand Radio SiteSurvey required)Attach IQ-Y Cable to RadioIQ NCC CartridgesAttach Straight-Cable forConnection Modules (CM)Client Satellite |
Related manuals for Rain Bird IQNCCRS
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved