Pioneer Premier DEH-P740MP Installation Manual

Also see for Premier DEH-P740MP: Service manual Service manual Operation manual Operation manual

Fig. 27 When not connecting a rearspeaker lead to a SubwooferFuseMulti-CD player(sold separately)IP-BUS cableUse this for connections when you have the separatelyavailable amplifier.Blue/whiteTo system control terminal of the power ampor Auto-antenna relay control terminal(max. 300 mA 12 V DC).Subwoofer outputor Non Fading OutputIP-Bus input(Blue)Antenna jackFront outputRear outputThis ProductConnecting cordswith RCA pin plugs(sold separately)System remote controlFront speakerFront speakerSubwoofer SubwooferRear speakerRear speakerFront speakerFront speakerRear speakerRear speakerGrayGray/blackVioletViolet/blackWhiteWhite/blackGreenGreen/blackOrange/whiteTo lightnig switch terminal.Black (ground)To vehicle (metal) body.With a 2 speaker system, do not connect anything tothe speaker leads that are not connected to speakers.Yellow/blackIf you use a cellular telephone, connect it via theAudio Mute lead on the cellular telephone. If not,keep the Audio Mute lead free of any connections.YellowTo terminal always suppliedwith power regardless ofignition switch position.RedTo electric terminal controlled byignition switch (12 V DC) ON/OFF.RightLeft16 cm [5/8 in]16 cm [5/8 in]+≠+≠≠ ≠+ ++≠+≠+≠+≠+≠+≠Power amp(sold separately)Power amp(sold separately)Power amp(sold separately)Note:• This unit is for vehicles with a 12-volt battery andnegative grounding. Before installing it in a recre-ational vehicle, truck, or bus, check the batteryvoltage.• To avoid shorts in the electrical system, be sure todisconnect the ≠ battery cable before beginninginstallation.• Refer to the owner’s manual for details on con-necting the power amp and other units, then makeconnections correctly.• Secure the wiring with cable clamps or adhesivetape. To protect the wiring, wrap adhesive tapearound them where they lie against metal parts.• Route and secure all wiring so it cannot touch anymoving parts, such as the gear shift, handbrakeand seat rails. Do not route wiring in places thatget hot, such as near the heater outlet. If the insula-tion of the wiring melts or gets torn, there is a dan-ger of the wiring short-circuiting to the vehiclebody.• Don’t pass the yellow lead through a hole into theengine compartment to connect to the battery. Thiswill damage the lead insulation and cause a verydangerous short.• Do not shorten any leads. If you do, the protectioncircuit may fail to work when it should.• Never feed power to other equipment by cuttingthe insulation of the power supply lead of the unitand tapping into the lead. The current capacity ofthe lead will be exceeded, causing overheating.• When replacing fuse, be sure to use only fuse ofthe rating prescribed on this unit.• Since a unique BPTL circuit is employed, neverwire so the speaker leads are directly grounded orthe left and right ≠ speaker leads are common.• Speakers connected to this unit must be high-power types with minimum rating of 50 W andimpedance of 4 to 8 ohms. Connecting speakerswith output and/or impedance values other thanthose noted here may result in the speakers catch-ing fire, emitting smoke, or becoming damaged.• When this product’s source is switched ON, a con-trol signal is output through the blue/white lead.Connect to an external power amp’s system remotecontrol or the car’s Auto-antenna relay control ter-minal (max. 300 mA 12 V DC). If the car featuresa glass antenna, connect to the antenna boosterpower supply terminal.• When an external power amp is being used withthis system, be sure not to connect the blue/whitelead to the amp’s power terminal. Likewise, do notconnect the blue/white lead to the power terminalof the auto-antenna. Such connection could causeexcessive current drain and malfunction.• To avoid short-circuiting, cover the disconnectedlead with insulating tape. Especially, insulate theunused speaker leads without fail. There is a possi-bility of short-circuiting if the leads are not insulat-ed.• To prevent incorrect connection, the input side ofthe IP-BUS connector is blue, and the output sideis black. Connect the connectors of the same colorscorrectly.• If this unit is installed in a vehicle that does nothave an ACC (accessory) position on the ignitionswitch, the red lead of the unit should be connectedto a terminal coupled with ignition switch ON/OFFoperations. If this is not done, the vehicle batterymay be drained when you are away from the vehi-cle for several hours. (Fig. 1)Fig. 1• The black lead is ground. Please ground this leadseparately from the ground of high-current prod-ucts such as power amps.If you ground the products together and the groundbecomes detached, there is a risk of damage to theproducts or fire.• Cords for this product and those for other productsmay be different colors even if they have the samefunction. When connecting this product to anotherproduct, refer to the supplied Installation manualsof both products and connect cords that have thesame function.No ACC positionACC positionONSTARTOFFACCONSTARTOFFPrinted in ThailandImprimé en Thaïlande

Connecting the Units This product conforms to CEMA cord colors.Le code de couleur des câbles utilisé pour ce produit estconforme à CEMA.This product conforms to CEMA cord colors.Le code de couleur des câbles utilisé pour ce produit estconforme à CEMA.INSTALLATION MANUALMANUEL D’INSTALLATIONDEH-P740MP