Pioneer Elite N-30 Operating Instructions Manual

Also see for Elite N-30: Operating instructions Service manual

Contents

Additional information1022EnWhen a USB storage device is connectedWhen computer is connected via USB cableProblem Check RemedyUSB storage device is notrecognized.Is the USB storage device properlyconnected?Connect the device securely (all the way in).Is the USB storage device connectedvia a USB hub?This unit does not support USB hubs. Connect the USBstorage device directly.This is not a problem with this unit. Turn the power off then back on.Some USB storage devices may not be recognized properly.This unit only supports USB mass storage class devices.Only the FAT16 and FAT32 file systems are supported. Otherfile systems (ex. FAT, NTFS, etc.) are not supported.This device does not support the use of external hard discdrives.A USB storage device isconnected and displayed,but the audio files storedon the USB storagedevice cannot be playedback.The audio files are copyrighted. Copyrighted audio files stored on a USB storage devicecannot be played back. Attempting to import music datafrom a CD, etc., to a computer may cause the invocation ofcopy protection, depending on the settings.The file format cannot be properlyplayed back on this unit.See the list of file formats that can be played back on thisreceiver (page 25).Much time is required torecognized the USBstorage device.What is the USB storage devicescapacity?Some time may be required to load the data when largecapacity USB storage devices are connected (this couldtake several minutes).Power is not supplied tothe USB storage device.Does an error message appear in thefront panel display?No power is supplied if the powerconsumption is too high.Turn the power off then back on.Turn the power off, then disconnect and reconnect the USBstorage device.Press FUNCTION to switch to the other mode, then switchagain to the USB mode. (When the input is switched back toUSB.)Problem Check RemedyWhen the DIGITAL INUSB port is connected toa computer via USBcable, audio files on thecomputer cannot beplayed.Has the proper device driver beeninstalled on the computer?When using a USB cable to connect the unit’s DIGITAL INUSB port to a computer in order to play audio files on thecomputer, the proper device driver must be downloadedfrom the Pioneer website and installed on your computer.Consult the Pioneer website for instructions on installingthe driver.NetworkNo sound is producedwhen attempting to playfiles on a computer.Are volume settings correct for theOS and application program?Raise the volume settings as required.Is the OS audio output set to MUTE? Cancel the MUTE setting.Are multiple applications runningsimultaneously?Try closing applications that are not in use.Are volume settings correct for theOS and application program?For audio device select “Pioneer USB Audio Device”.Problem Check RemedyCannot access to thenetwork.The LAN cable is not firmlyconnected.Firmly connect the LAN cable (page 7).The router is not switched on. Switch on the router.Cannot access to thecomponent or PCconnected via network.Internet security software is currentlyinstalled in the connectedcomponent.There are cases where a component with Internet securitysoftware installed cannot be accessed.The audio component on the networkwhich has been switched off isswitched on.Switch on the audio component on the network beforeswitching on this unit.The component connected to thenetwork is not properly set.If the client is automatically authorized, you need to enterthe corresponding information again. Check whether theconnection status is set to “Do not authorize”.There are no playable audio files onthe component connected to thenetwork.Check the audio files stored on the component connected tothe network.Playback does not start. The component is currentlydisconnected from this receiver orthe power supply.Check whether the component is properly connected to thisreceiver or the power supply.The PC or Internet radio isnot properly operated.The corresponding IP address is notproperly set.Switch on the built-in DHCP server function of your router,or set up the network manually according to your networkenvironment (page 19).The IP address is being automaticallyconfigured.The automatic configuration process takes time. Pleasewait.Problem Check Remedy