Pioneer DEQ-P7050 Installation Manual

Also see for DEQ-P7050: Operation manual

Connecting to a sold separately power ampThis product can be connected to a sold separately power amp using the RCA output jacks.Connecting the power cordNote:• This unit is for vehicles with a 12-volt batteryand negative grounding. Before installing it in arecreational vehicle, truck, or bus, check the bat-tery voltage.• To avoid shorts in the electrical system, be sureto disconnect the · battery cable before begin-ning installation.• Refer to the owner’s manual for details on con-necting the power amp and other units, thenmake connections correctly.• Secure the wiring with cable clamps or adhesivetape. To protect the wiring, wrap adhesive tapearound them where they lie against metal parts.• Route and secure all wiring so it cannot touchany moving parts, such as the gear shift, hand-brake and seat rails. Do not route wiring inplaces that get hot, such as near the heater outlet.If the insulation of the wiring melts or gets torn,there is a danger of the wiring short-circuiting tothe vehicle body.• Don’t pass the yellow lead through a hole intothe engine compartment to connect to the battery.This will damage the lead insulation and cause avery dangerous short.• Do not shorten any leads. If you do, the protec-tion circuit may fail to work when it should.• Never feed power to other equipment by cuttingthe insulation of the power supply lead of theunit and tapping into the lead. The current capac-ity of the lead will be exceeded, causing over-heating.• When replacing fuse, be sure to use only fuse ofthe rating prescribed on the fuse holder.• Since a unique BPTL circuit is employed, neverwire so the speaker leads are directly grounded orthe left and right · speaker leads are common.• Speakers connected to this unit must be high-power types with minimum rating of 50 W andimpedance of 4 to 8 ohms. Connecting speakerswith output and/or impedance values other thanthose noted here may result in the speakers catch-ing fire, emitting smoke or becoming damaged.• When this product’s source is switched ON, acontrol signal is output through the blue/whitelead. Connect to an external power amp’s systemremote control or the car’s Auto-antenna relaycontrol terminal (max. 300 mA 12 V DC). If thecar features a glass antenna, connect to the anten-na booster power supply terminal.• When an external power amp is being used withthis system, be sure not to connect the blue/whitelead to the amp’s power terminal. Likewise, donot connect the blue/white lead to the power ter-minal of the auto-antenna. Such connection couldcause excessive current drain and malfunction.• To avoid short-circuiting, cover the disconnectedlead with insulating tape. Especially, insulate theunused speaker leads without fail. There is a pos-sibility of short-circuiting if the leads are notinsulated.• To prevent incorrect connection, the input side ofthe IP-BUS or optical cable connector is blue,and the output side is black. Connect the connec-tors of the same colors correctly.• If this unit is installed in a vehicle that does nothave an ACC (accessory) position on the ignitionswitch, the red lead of the unit should be con-nected to a terminal coupled with ignition switchON/OFF operations. If this is not done, the vehi-cle battery may be drained when you are awayfrom the vehicle for several hours.• The black lead is ground. Please ground this leadseparately from the ground of high-current prod-ucts such as power amps.If you ground the products together and theground becomes detached, there is a risk of dam-age to the products or fire.• To ensure proper heat dissipation of this product,take special care not to block the cooling fan sideof this product.No ACC positionACC positionONSTARTOFFACCONSTARTOFFConnecting the Units • Cords for this product and those for other prod-ucts may be different colors even if they havethe same function. When connecting this prod-uct to another product, refer to the suppliedInstallation manuals of both products and con-nect cords that have the same function.INSTALLATION MANUALDEQ-P7050Printed in Japan

This product conforms to new cord colors.Gray/blackWhite/blackGreen VioletLeft RightWhite GrayGreen/black Violet/blackFront speaker Front speakerRear speaker Rear speakerThis productYellowTo terminal always supplied withpower regardless of ignition switchposition.Fuse holderBlack (ground)To vehicle (metal) body.Blue/whiteTo system control terminal of the poweramp or Auto-antenna relay control terminal(max. 300 mA 12 V DC).Do not connect anything to the speakerleads that are not connected to speakers.BlackBlack/whiteCenter speaker+≠+≠+≠+≠+≠When you connect a power amp (soldseparately), be sure to use the blue/whitelead of this unit. If you use the blue/whitelead of the head unit, it causes noises.This productBlue/whiteTo system control terminal of the poweramp or Auto-antenna relay control terminal(max. 300 mA 12 V DC).+≠+≠+≠+≠+≠+≠Front speaker Front speakerRear speaker Rear speakerCenter speaker SubwooferSystem remote controlRCA cables(sold separately)Power amp(sold separately)Subwoofer outputRear outputFront output Center outputPower amp(sold separately)Power amp(sold separately)Power amp(sold separately)When you connect a power amp (soldseparately), be sure to use the blue/whitelead of this unit. If you use the blue/whitelead of the head unit, it causes noises.

/ 2

Related manuals for Pioneer DEQ-P7050