Pioneer DEH-P9400MP Installation Manual

Also see for DEH-P9400MP: Catalog Operation manual Installation manual Operation manual Operation manual

Connection diagram for standard modeFig. 215 cm(5/8 inch)Gray/blackWhite/blackGreen Violet+≠+≠+≠Power amp(sold separately)+≠+≠+≠+≠+≠+≠+≠Power amp(sold separately)Power amp(sold separately)Blue/whiteTo system control terminal of the power ampor Auto-antenna relay control terminal (max.300 mA 12 V DC).System remote controlLeft RightRear speaker Rear speakerFuse resistorYellowTo terminal always supplied withpower regardless of ignition switchposition.RedTo electric terminal controlled byignition switch (12 V DC) ON/OFF.Black (ground)To vehicle (metal) body.Orange/whiteTo lighting switch terminal.Fuse resistorWhite GrayGreen/black Violet/blackRear speaker Rear speakerThis ProductAntenna jackSubwooferFront speakerConnecting cords with RCA pinplugs (sold separately)IP-BUS cableIP-BUS input (Blue)Multi-CD player(sold separately)SubwooferFront speakerFuse holderFront speaker Front speakerYellow/blackIf you use a cellular telephone,connect it via the Audio Mute lead onthe cellular telephone. If not, keep theAudio Mute lead free of anyconnections.Perform these connections when using adifferent amp (sold separately).15 cm(5/8 inch)With a 2 speaker system, do not connectanything to the speaker leads that are notconnected to speakers.15 cm (5/8 inch)DSP switchSwitch the DSP switch asillustration below.Subwoofer output(LOW/SUBWOOFER OUTPUT)Rear output(MID/REAR OUTPUT)Front output (HIGH/FRONT OUTPUT)23 cm (7/8 inch)Note:• This unit is for vehicles with a 12-volt battery andnegative grounding. Before installing it in a recre-ational vehicle, truck, or bus, check the batteryvoltage.• To avoid shorts in the electrical system, be sure todisconnect the ≠ battery cable before beginninginstallation.• Refer to the owner’s manual for details on con-necting the power amp and other units, then makeconnections correctly.• Secure the wiring with cable clamps or adhesivetape. To protect the wiring, wrap adhesive tapearound them where they lie against metal parts.• Route and secure all wiring so it cannot touch anymoving parts, such as the gear shift, handbrake,and seat rails. Do not route wiring in places thatget hot, such as near the heater outlet. If the insula-tion of the wiring melts or gets torn, there is a dan-ger of the wiring short-circuiting to the vehiclebody.• Don’t pass the yellow lead through a hole into theengine compartment to connect to the battery. Thiswill damage the lead insulation and cause a verydangerous short.• Do not shorten any leads. If you do, the protectioncircuit may fail to work when it should.• Never feed power to other equipment by cuttingthe insulation of the power supply lead of the unitand tapping into the lead. The current capacity ofthe lead will be exceeded, causing overheating.• When replacing fuse, be sure to use only fuse ofthe rating prescribed on the fuse holder.• Since a unique BPTL circuit is employed, neverwire so the speaker leads are directly grounded orthe left and right ≠ speaker leads are common.• If the RCA pin jack on the unit will not be used, donot remove the caps attached to the end of the con-nector.• Speakers connected to this unit must be high-power types with minimum rating of 50 W andimpedance of 4 to 8 ohms. Connecting speakerswith output and/or impedance values other thanthose noted here may result in the speakers catch-ing fire, emitting smoke, or becoming damaged.• When this product’s source is switched ON, a con-trol signal is output through the blue/white lead.Connect to an external power amp’s system remotecontrol or the car’s Auto-antenna relay control ter-minal (max. 300 mA 12 V DC). If the car featuresa glass antenna, connect to the antenna boosterpower supply terminal.• When an external power amp is being used withthis system, be sure not to connect the blue/whitelead to the amp’s power terminal. Likewise, do notconnect the blue/white lead to the power terminalof the auto-antenna. Such connection could causeexcessive current drain and malfunction.• To avoid short-circuiting, cover the disconnectedlead with insulating tape. Especially, insulate theunused speaker leads without fail. There is a possi-bility of short-circuiting if the leads are not insulat-ed.• To prevent incorrect connection, the input side ofthe IP-BUS connector is blue, and the output sideis black. Connect the connectors of the same colorscorrectly.• If this unit is installed in a vehicle that does nothave an ACC (accessory) position on the ignitionswitch, the red lead of the unit should be connectedto a terminal coupled with ignition switch ON/OFFoperations. If this is not done, the vehicle batterymay be drained when you are away from the vehi-cle for several hours. (Fig. 1)Fig. 1• The black lead is ground. Please ground this leadseparately from the ground of high-current prod-ucts such as power amps.If you ground the products together and the groundbecomes detached, there is a risk of damage to theproducts or fire.No ACC positionACC positionONSTARTOFFACCONSTARTOFFDEH-P9400MPPrinted in JapanImprimé au Japon

Connecting the Units This product conforms to CEMA cord colors.Le code de couleur des câbles utilisé pour ce produit estconforme à CEMA. • Cords for this product and those for other prod-ucts may be different colors even if they have thesame function. When connecting this product toanother product, refer to the supplied Installationmanuals of both products and connect cords thathave the same function.INSTALLATION MANUALMANUEL D’INSTALLATION