DEH-P860MP/XN/UC 575 6 7 85 6 7 8CDFABE[BAND][BAND][BAND][BAND][BAND]Power On(T.Offset is adjusted)TRK 00 MIN00 SECSEC00[CD]or[SOURCE]Source OnTRK MIN[4]+[6]+Reset or[4]+[6]+BU+ACCTest Mode In[3][1][1]Power On(T.Offset is not adjusted)TRK 99 MIN 99 SEC 99[2][2][2][2]Power OffTRK MIN SECPower OffTRK MIN SECPower OffTRK MIN SECPower OffTRK MIN SECFocus CloseS.Curve checkTRK 91 MIN91 SEC 91[6] [1][3][6][3]Focus Modeswitching*2TRK 0x MIN 0x SEC 0xTracking ServoCloseTRK00 MIN00 SEC00or TRK 99 MIN99 SEC 99CRG- *8TRK 00 MIN00 SEC 00or TRK 99 MIN 99 SEC 99[→] [←][→] [←][→] [←]CRG+ *8*9TRK00 MIN00 SEC00or TRK 99 MIN 99 SEC 99Automatic adjustmentdisplay switching*3TRK ?? MIN ?? SEC ??Applicable servomechanismTRK?tr MIN?minSEC?sec[6][3]T.CloseApplicable servomechanismTRK MIN SECRF AGC /RF AGC coefficient displayTRK ?? MIN ?? SEC ??CRG+TRK8x MIN8x SEC8xor TRK 9x MIN 9x SEC 9xCRG-TRK 8x MIN8x SEC 8xor TRK 9x MIN 9x SEC 9xT.Balance adjustment /T.Balance coefficient displayTRK ?? MIN ?? SEC ??F, T, RF AGCF.Bias display switching*7TRK ?? MIN?? SEC ??F, T AGC / F.BiasRF AGCTRK MIN SECCRG/TR Jump *5value switchingTRK MIN SECCRG/TR Jump +*4TRK MIN SECCRG/TR Jump -*4*6TRK MIN SECTracking OpenTRK 8x MIN 8x SEC 8xor TRK 9xMIN 9xSEC 9xTracking OpenTRK8x MIN8x SEC8xor TRK 9x MIN 9x SEC 9x[Key][BAND][→][6][1][2][3]Power On/OffCRG + / TR Jump +(Direction of the external surface)CRG - / TR Jump -(Direction of the internal surface)T.CLS and AGC and Applicable servomechanism /AGC, AGC display switchingRF Gain switching / Offset adjustment display /T.Balance adjustment / T.OpenF.Close, S.Curve / Rough Servo and RF AGC / F, T, RF AGCSPDL 1X/2X switchingAs for the double speed (2x), audio output cannot be supported.F. Mode switching / Tracking Close / CRG, TR Jump switchingTest ModeOperation[KEY]ContentsDisplay*1) TYP → -6dB → -12dBTRK MIN SEC TRK 06 MIN 06 SEC 06 TRK 12 MIN 12 SEC 12*2) Focus Close → S.Curve ckeck setting → F EQ measurement settingTRK 00 MIN 00 SEC 00 TRK 01 MIN 01 SEC 01 TRK 02 MIN 02 SEC 02(TRK 99 MIN 99 SEC 99)*3) F.Offset Display → T.Offset Display → Switch to the order of the original display*4) 1TR / 32TR / 100TR*5) Single TR → 32TR → 100TR → CRG Move9x(8x) : 91(81) 92(82) 93(83) 94(84)*6) Only at the time of CRG Move, 100TR Jump*7) TRK/MIN/SEC → F.AGC → T.AGC → F.Bias → RF AGC*8) CRG motor voltage = 2[V][←]Error Rate measurement 1st-ON : ERR count beginning(30Sec)2nd-ON : BER display data[%][4][5]- Flow ChartRF AMPGain switchingTRK GGMIN GGSEC GG[2]SPINDLESpeed switchingTRK SP MIN SP SEC SP[4]*1T.Close and AGC*9) TYP(1X) → 2X → 1XTRK MIN SEC TRK 22 MIN 22 SEC 22 TRK 11 MIN 11 SEC 11As for the double speed (2x), audio output cannot be supported.TYP(2X) → 1X → 2XTRK MIN SEC TRK 11 MIN 11 SEC 11 TRK 22 MIN 22 SEC 22?tr ?min ?sec?tr ?min ?sec?tr ?min ?sec?tr ?min ?sec?tr ?min ?sec