CAUTION:• PIONEER does not recommend that youinstall or service your display yourself.Installing or servicing the product mayexpose you to risk of electric shock orother hazards. Refer all installation andservicing of your display to authorizedPioneer service personnel.• Secure all wiring with cable clamps orelectrical tape. Do not allow any barewiring to remain exposed.• Do not drill a hole into the engine com-partment to connect the yellow lead ofthe unit to the vehicle battery. Enginevibration may eventually cause the insu-lation to fail at the point where the wirepasses from the passenger compartmentinto the engine compartment. Take extracare in securing the wire at this point.• It is extremely dangerous to allow thedisplay lead to become wound aroundthe steering column or gearshift. Be sureto install the display in such a way that itwill not obstruct driving.• Make sure that wires will not interferewith moving parts of the vehicle, such asthe gearshift, parking brake or seat slid-ing mechanism.• Do not shorten any leads. If you do, theprotection circuit may fail to work prop-erly.WARNINGLIGHT GREEN LEAD AT POWER CONNEC-TOR IS DESIGNED TO DETECT PARKEDSTATUS AND MUST BE CONNECTED TOTHE POWER SUPPLY SIDE OF THE PARK-ING BRAKE SWITCH. IMPROPER CONNEC-TION OR USE OF THIS LEAD MAY VIOLATEAPPLICABLE LAW AND MAY RESULT INSERIOUS INJURY OR DAMAGE.WARNING• To avoid the risk of accident and the potential vio-lation of applicable laws, the front DVD or TV(sold separately) feature should never be usedwhile the vehicle is being driven. Also, RearDisplays should not be in a location where it is avisible distraction to the driver.• In some countries or states the viewing of imageson a display inside a vehicle even by persons otherthan the driver may be illegal. Where such regula-tions apply, they must be obeyed and this unit'sDVD features should not be used.INSTALLATION MANUAL <05A00000>AVH-P5750DVDPrinted in Japan RCConnecting the Units ENGLISH>Note:• This unit is for vehicles with a 12-volt battery andnegative grounding. Before installing it in a recre-ational vehicle, truck, or bus, check the batteryvoltage.• To avoid shorts in the electrical system, be sure todisconnect the ≠ battery cable before beginninginstallation.• Refer to the owner’s manual for details onconnecting the power amp and other units, thenmake connections correctly.• Secure the wiring with cable clamps or adhesivetape. To protect the wiring, wrap adhesive tapearound them where they lie against metal parts.• Route and secure all wiring so it cannot touch anymoving parts, such as the gear shift, handbrake andseat rails. Do not route wiring in places that gethot, such as near the heater outlet. If the insulationof the wiring melts or gets torn, there is a danger ofthe wiring short-circuiting to the vehicle body.• Don’t pass the yellow lead through a hole into theengine compartment to connect to the battery. Thiswill damage the lead insulation and cause a verydangerous short.• Do not shorten any leads. If you do, the protectioncircuit may fail to work when it should.• Never feed power to other equipment by cuttingthe insulation of the power supply lead of the unitand tapping into the lead. The current capacity ofthe lead will be exceeded, causing overheating.• When replacing the fuse, be sure to only use a fuseof the rating prescribed on the fuse holder.• Since a unique BPTL circuit is employed, neverwire so the speaker leads are directly grounded orthe left and right ≠ speaker leads are common.• If the RCA pin jack on the unit will not be used, donot remove the caps attached to the end of the con-nector.• Speakers connected to this unit must be high-power with minimum rating of 50 W and imped-ance of 4 to 8 ohms. Connecting speakers with out-put and/or impedance values other than thosenoted here may result in the speakerscatching fire, emitting smoke or becoming dam-aged.• When this product’s source is switched ON, a con-trol signal is output through the blue/white lead.Connect to an external power amp’s system remotecontrol or the car’s Auto-antenna relay control ter-minal (max. 300 mA 12 V DC). If the car featuresa glass antenna, connect to the antenna boosterpower supply terminal.• When an external power amp is being used withthis system, be sure not to connect the blue/whitelead to the amp’s power terminal. Likewise, do notconnect the blue/white lead to the power terminalof the auto-antenna. Such connection could causeexcessive current drain and malfunction.• To avoid a short-circuit, cover the disconnectedlead with insulating tape. Insulate the unusedspeaker leads without fail. There is a possibility ofa short-circuit if the leads are not insulated.• To prevent incorrect connection, the input side ofthe IP-BUS connector is blue, and the output sideis black. Connect the connectors of the samecolors correctly.• This unit cannot be installed in a vehicle thatdoes not have an ACC (accessory) position onthe ignition switch. (Fig. 1)Fig. 1• The black lead is ground. Please ground this leadseparately from the ground of high-current prod-ucts such as power amps.If you ground the products together and the groundbecomes detached, there is a risk of damage to theproducts or fire.No ACC positionACC positionONSTARTOFFACCONSTARTOFF• Cords for this product and those for other productsmay be different colors even if they have the samefunction. When connecting this product to anotherproduct, refer to the supplied manuals of bothproducts and connect cords that have the samefunction.This product conforms to new cord colors.
