Pioneer AS-WL300 Getting Started Manual

Also see for AS-WL300: Getting started guide Getting started guide Getting started Getting started

Contents

....--- Please connect using either method.---,STEP2 Connect the Unit (WPS)0 e This procedure explains how to connect the unit using the WPSfunction. If the base does not have a WPS function. refer to the"Manual" procedure below.e Do not connect the LAN cable to the unit until instructed.e When using multiple units of this product. the IP address of this unitneeds to be changed. Refer to "Troubleshooting" on the reverse.1 . Switch an the unit0 Switch off the AV device.AV RECEIVER Blu-ray Disc playerConnect the POWER connector on the unit to the USB port on theAV device using the USB end of the supplied feeder cable.~ITJ ·I• The location of the USBport and its name mayvary depending on thedevice. If you cannotlocate a USB port. referto the device's user'smanual for help.Switch on the AV device.A USB port is thehorizontallyCor vertically) long port(as shown above).* On some devices. it islabelled [DC OUTPUTfor WIRELESS LAN].AV RECEIVERIf= ]1Blu-ray Disc playerAV RECEIVER Blu-ray Disc playerCheck that the "(.!,)(POWER)" , "g (WPS)" and "~(WIRELESS)"indicators on the unit are lit."' Once the indicators light up, wait2 minutes before proceeding.~ .. ,...•Lit2. Connect the Unit0fJPress the "WPS" button on the base. Refer to the base user's manuallor more details on the WPS button.Press and hold the "WPS" button on the back of the unit until theWPS indicator on the front flashes. (over 2 seconds).Press and hold for over 2 seconds The WPS indicator (centre) will flash~Q I......uo~Check that the WPS indicator on the unit changes from a flashing lightto a steadily lit light.* If the WPS indicator stops flashing and is steadily lit.the unit is connected to the Wireless LAN.(The unit is not connected if the WPS indicator isflashing.)* If the WPS indicator does not flash. press the "WPS"button again.* If the WPS indicator stops flashing and turns off.the ~wPS" buttonDisconnect the USB feeder cable end of the supplied cable thatis connected to the unit.-~---'1 ~~~~=~:Blu-ray Disc playerConnection to the base is now complete. Continue to Step 3.STEP2 Connect the Unit (Manual)0 e Use this procedure to manually connect the unit. especially if connectingthe unit using the "WPS" procedure. above. does not work.e If the computer on which you will configure the unit is connected to theWireless LAN cable disconnect it.e When using multiple units of this product. the IP address of this unitneeds to be changed. Refer to "Troubleshooting" on the reverse.1 . Search far a Network ConnectionBefore connecting or configuring this unit, you must know the Wireless LANsettings for your base. Write the settings in the table below.• Refer to the base user's manual for details on the Wireless LAN settings.• When using WEP security settingsName Wireless LAN settings(1) SSID (Network name)(2) Authentication O OPEN 0 SHARED(3) Authentication key method 0 Hexadecimal" 1 0 ASCII'2(4) Default key 0 Key 1 0 Key2 0 Key3 0 Key4(5) Encryption key• 1: 1&dr g rt number (0-9, A-F) 2. ASCII ( 1-byte letters and numbers. rnc!udrng upper and lowercase !etters)• When using WPA/WPA2 security settingsName Wireless LAN Settings(1) SSID (Networf< name)(2) Authentication O WPA-PSK O WPA2-PSK{3) Authentication key 0 Hexadecimal" 1 0 ASCII'2(4) Encryption O TKIP O AES(5) Encryption key• 1 : 1&dreut number (0-9, A-F) 2. ASCII ( 1-byte letters and numbers. rncludrng upper and lowercase letters)0 This unit cannot connect to a base with a SSID (Network name) that Includes a semicolon(;).Refer to the base user's manual for details on changing the SSID.2. Connect to the Computero Switch ott the computer. ~Connect the ETHERNET port on the unit to the computer LAN porton the computer using the LAN end of the supplied feeder cable.o[1 . J* The location of the LAN port and its name may varydepending on the computer. If you cannot locate a LANport. refer to the computer user's manual for help.The LAN port is the large port that is slightlylarger than a telephone modular jack.• Some bases have LAN written on them.Connect the POWER connector on the unit to the USB port onthe computer using the USB end of the supplied feeder cable.* The location of the USB port and its name mayvary depending on the device. If you cannotlocate a USB port. refer to the device's user's1 manual for help.~-9A USB port is the horizontally (or vertically) longport (as shown above).• On some computers. it is labelled "USB" ormarked by a ·~·.Switch on the computer.Check that the"(.!,) (POWER)" . "g CWPS)" and • '9' (WIRELESS)"indicators on the unit are lit.• Once the indicators light up, wait2 minutes before proceeding.3. Configure the Unito Launch the Web browser.fJ Enter "cv.setup" in the Addressbar and press .Lit0 If you cannot display the Web Configuration window by entering ~cv.setuo". enter"192.168.1.249" and proceed toiJ.If the window still does not open, refer to"Troubleshooting~ on the reverse.CD Enter "admin" as the user nameand "password" the password.® Click [OK].0 If you camot log in to the WebConfiguration window. check that youhave entered the settings, correctly.,,.._'""_ .. .u-..u.,.......----=:---===--=·~-( ~~ )CDG:).Continued over the page