Panasonic WV-SW175 Installation Manual

Also see for WV-SW172: Product catalog Operating instructions Operating instructions Specification Installation guide

Contents

installation guide

Panasonic WV-SW175 Installation Manual Manual pdf 1 page image

OptionPrecautions for use Precautions for InstallationStandard accessoriesThis product has no power switch.When turning off the power, disconnect the power supply from the 12 V DC power supply or thePoE device. (When using both the 12 V DC power supply and the PoE device for power supply, dis-connect both the connections.)To keep on using with stable performanceDo not use this camera in hot and humid conditions for a long time. Failure to observe this causescomponent degradation resulting in life shortening of this product.Do not expose this camera to direct heat sources such as a heater.Do not touch the lens cover with your bare hands.A dirty lens cover causes deterioration of picture quality.Handle this camera with care.Do not drop this camera, nor apply shock or vibration to this camera. Failure to observe this maycause trouble.About the PC monitorDisplaying the same image on a monitor for a long time may damage the monitor. It is recommend-ed to use a screen-saver.When an error is detected, this product will restart automatically.This product will be inoperable for around 2 minutes after the restart just as when the power is turned on.Product disposal/transferData saved on this product or a storage device used with this product may lead to personalinformation leakage. When it is necessary to dispose or give this product to someone, even whenfor repair, make sure that there is no data on this product.Cleaning this product bodyBe sure to turn off the power before cleaning. Failure to observe this may cause injury. Do not usestrong abrasive detergent when cleaning this product. Otherwise, it may cause discoloration. Whenusing a chemical cloth for cleaning, read the caution provided with the chemical cloth product.When the dirt is hard to remove, use a damp cloth and wipe the dirty areas. Then, wipe with a drycloth to remove any moisture.Transmission intervalImage transmission interval may become slow depending on the network environment,PC performance, shooting subject, access number, etc.About SD memory cardWhen using an unformatted SD memory card, format it using this camera. Recorded data on the⿟SD memory card will be deleted when formatted. If an unformatted SD memory card or an SDmemory card formatted with other devices is used, this product may not work properly or perfor-mance deterioration may be caused. Refer to the Operating Instructions (included in theCD-ROM) for how to format a SD memory card.When some SD memory cards are used with this product, the product may not work properly or⿟performance deterioration may be caused. Use the SD memory cards recommended.Code labelThe code labels (accessory) are required at inquiry for trouble. Use caution not to lose these labels.It is recommended to paste one of the labels onto the CD-ROM case.About the MOS image sensorWhen continuously shooting a bright light source such as a spotlight, the color filter of the MOS⿟image sensor may have deteriorated and it may cause discoloration. Even when changing thefixed shooting direction after continuously shooting a spotlight for a certain period, the discolor-ation may remain.When shooting fast-moving subjects or performing panning/tilting operations, objects crossing⿟the shooting area may look to be bending askew.AVC Patent Portfolio LicenseTHIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THEPERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVEREMUNERATION TO(i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR(ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONALACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVCVIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONALINFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C.SEE HTTP://WWW.MPEGLA.COMFlickeringDue to the influence of lighting, flickering may sometimes happen. In this case, select “Indoorscene” for “Light control mode”. Select “Indoor scene(50Hz)” or “Indoor scene(60Hz)” in accor-dance with the power supply frequency in your locality. Refer to the Operating Instructions (includedin the CD-ROM) for further information about the setting.Under extremely strong lighting, flickering may happen even when “Indoor scene” is selected for“Light control mode”. When the brightness (illuminance) level on the screen is set to a relatively lowlevel with the [Brightness] buttons, flickering may frequently happen. In such cases, either of the fol-lowing can reduce flickering.Moderate the illumination intensities of objects by changing the camera direction.⿟⿟ Set the brightness (illuminance) level on the screen to a brighter level with the [Brightness] buttons.White-out on images caused by the effect of light control modeWhen “Indoor scene” is selected for “Light control mode”, the tone of the brighter parts on thescreen may be deteriorated than the case when “ELC” is selected.Color blurring on detailed drawing patternsWhen there are detailed drawing patterns on images, color blurring may happen over these parts.Consumable partsThe following are consumables: Replace them in accordance with their lives. Their lives varydepending on use environment and conditions. Lifetime is just an indication when using the cameraat +20 °C {68 °F}.Panning motor, tilting motor, flat cable for tilting: Approx. 3.7 million operations.⿟Lens and pan/tilt headIf a lens and pan/tilt head are not performed for a long period of time, the grease coating insidethese parts may become sticky. That may obstruct the parts from moving. To prevent this, movethe lens or pan/tilt head periodically.Panasonic assumes no responsibility for injuries or property damage resulting fromfailures arising out of improper installation or operation inconsistent with thisdocumentation.Installation area for this productSelect an appropriate place for the installation area (such as a strong wall or ceiling) in your par-⿟ticular environment.Avoid installing the camera in locations where it can be exposed to direct sunlight or rain from all⿟directions. Install the camera in an appropriate location such as on an exterior wall of a building.Do not place this product in the following places:Locations where a chemical agent is used such as a swimming pool⿟Locations subject to humidity, dust, steam and oil smoke⿟Locations that have a specific environment that is subject to an inflammable atmosphere or solvents⿟Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated⿟Locations where corrosive gas is produced, Locations where it may be damaged by briny air⿟such as seashoresLocations where the temperature is not within the specified range (-20° to +50°{-4° to +122°F}).⿟Locations subject to vibrations (This product is not designed for on-vehicle use.)⿟Locations subject to condensation as the result of severe changes in temperature⿟Be sure to remove this product if it is not in use.Before installationWhen this camera is mounted on a wooden ceiling or a wall, use the wood screws (accessory,⿟Screw B). Screws to be used for other materials are not provided. Prepare the screws accordingto the material, structure, strength and other factors of the mounting area and the total weight ofobjects to be mounted.Ensure that the mounting surface, anchor and screws are sufficiently strong.⿟Do not mount this product on a plaster board or a wooden section because they are too weak. If⿟this product is unavoidably mounted on such a section, the section shall be sufficiently reinforced.Design and engineer the power supply system to turn on/off the power of this product.The product has no power switch. When installing the product, use a power supplydevice equipped with the ON-OFF switch for servicing.About the network connectionWhen connecting to a network using the network cable of this product, observe the following.When wiring for the network, design and engineer not to be affected by thunder.Screw tighteningThe screws and bolts must be tightened with an appropriate tightening torque according to the⿟material and strength of the installation area.Do not use an impact driver. Use of an impact driver may damage the screws or cause tighten-⿟ing excessively.When a screw is tightened, make the screw at a right angle to the surface. After tightening the⿟screws or bolts, perform visual check to ensure tightening is enough and there is no backlash.Procure fixing screws separately.The screws that secure this product are not supplied. Prepare them according to the material andstrength of the area where the product is to be installed.Required pull-out capacity of a single screw/bolt is 294 N {66.09 lbf} or more.Fall prevention measuresWhen the external safety wire is connected, select a connection point resulting in that nothing willhit people after the stand is damaged.Do not remove or loosen the internal camera screws.Do not loosen the internal camera screws. Otherwise, water exposure may cause damage or mal-function of camera, or camera dropping may result in injury.Radio disturbanceWhen this product is used near TV/radio antenna, strong electric field or magnetic field (near amotor, a transformer or a power line), images may be distorted and noise sound may be produced.PoE (Power over Ethernet)Use a PoE hub/device that is compliant with IEEE802.3af standard.RouterWhen connecting this product to the Internet, use a broadband router with the port forwardingfunction (NAT, IP masquerade). Refer to the Operating Instructions (included in the CD-ROM) for fur-ther information about the port forwarding function.Time & date settingIt is necessary to set the time & date before putting this product into operation. Refer to theOperating Instructions on the provided CD-ROM for descriptions of how to perform the settings.CPU: Intel® CoreTM 2 Duo 2.4 GHz or faster recommendedMemory: 512 MB or more (A minimum of 1 GB memory is required when usingMicrosoft® Windows® 7 or Microsoft® Windows Vista®.)Network interface: 10BASE-T/100BASE-TX 1 portMonitor: Image capture size: 1024 x768 pixels or moreColor: 24-bit True color or betterOS: Microsoft® Windows® 7Microsoft® Windows Vista®Microsoft® Windows® XP SP3Web browser: Windows® Internet Explorer® 9.0 (32-bit)Windows® Internet Explorer® 8.0 (32-bit)Windows® Internet Explorer® 7.0 (32-bit)Microsoft® Internet Explorer® 6.0 SP3Others: CD-ROM drive(It is necessary to read the operating instructions and use the software onthe provided CD-ROM.)DirectX® 9.0c or laterAdobe® Reader®(It is necessary to view PDF file on the provided CD-ROM.)IMPORTANTWhen using a PC that does not meet the above requirements, displaying of images may⿟become slower or the web browser may become inoperable.Microsoft Windows 7 Starter, Microsoft Windows Vista Starter and Microsoft Windows XP⿟Professional 64-bit Edition are not supported.When using IPv6 for communication, use Microsoft Windows7 or Microsoft Windows Vista.⿟NoteRefer to “Notes on Windows⿟ ® / Internet Explorer ® versions” (included in the CD-ROM) forfurther information about system requirements for a PC and precautions when usingMicrosoft Windows 7, Microsoft Windows Vista or Internet Explorer.⿟ If using Microsoft Windows XP, screen tearing* may occur when the shooting scene drasticallychanges (for example, while shooting fast-moving subjects) due to the GDI restrictions of the OS.* A phenomenon in which portions of the screen are displayed out of alignment.For information on the operation verification of the supported operating systems and web⿟browsers, refer to our website at http://panasonic.net/pss/security/support/index.html.System requirements for a PCMain Unit (1 pc.) Flexible Stand (1 pc.) Connector Cover (1 pc.) Sunshade (1 pc.)Screw A (5 pcs.) Screw B (4 pcs.) Washer S (1 pc.) Washer L (1 pc.)Safety Wire (1 pc.) Self Bonding Tape(1 pc.)Foam Strip (1 pc.) Power cable plug (1 pc.)Installation Guide (this document) ........ (1 pc.)Warranty card (P model) ....................... (1 pc.)CD-ROM*1 ............................................ (1 pc.)Code label*2.......................................... (1 pc.)*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.*2 This label may be required for network management. The network administrator shall retain the code label.Installation GuideNetwork CameraModel No. WV-SW175/WV-SW172WV-SW175E/WV-SW172EPGQX1099YA Cs1011-1121Printed in China Main functions● Corresponding to outdoor useThis unit complies with waterproof and is able to install outdoors. (JIS C0920 compliant IP55)● H.264 and JPEG triple encodingA total of 3 outputs, comprising of 2 H.264 outputs and 1 JPEG output, can be provided.● Power over Ethernet functionWhen connecting with a PoE (Power over Ethernet) device, power will be supplied by simplyconnecting a LAN cable. (IEEE802.3af compliant)● Adaptive darkness correction modeCorrects the blacked-out parts of dark areas of objects that have different illumination intensities.● Panning/tilting function and preset position functionA single camera provides wide area monitoring.● Interactive communication with audioBy using the audio output connector and the microphone in connector, receiving audio from thecameras on a PC and transmitting audio from the PC to the cameras is available.● SDHC/SD memory card slot equippedIt is possible to save H.264 videos and JPEG images on the SDHC/SD memory card manually atan alarm occurrence, during the period of the schedule, or on a web browser. It is also possibleto save JPEG images at a network failure occurrence. (Download is possible.)Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe⿟Systems Incorporated in the United States and/or other countries.Microsoft, Windows, Windows Vista, Internet Explorer, ActiveX, and DirectX are either registered⿟trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.⿟Intel and Intel Core are trademarks or registered trademarks of Intel Corporation in the United⿟States and other countries.iPad, iPhone, and iPod touch are registered trademarks of Apple Inc., registered in the U.S. and⿟other countries.All other trademarks identified herein are the property of their respective owners.⿟Trademarks and registered trademarksConfirm the following items are included in the camera’s packaging.You will need the following additional items to install and configure the camera.[Locally procured]PoE device (When supplying the power using the PoE device)⿟a PC (see the system requirements in the Important Information document)⿟a router⿟a LAN cable (CAT-5 straight cable)⿟AC Adaptor (1 pc.)⿟As you will use this unit connected to a network, your attention is called to the following security risks.A Leakage or theft of information through this unitB Use of this unit for illegal operations by persons with malicious intentC Interference with or stoppage of this unit by persons with malicious intentIt is your responsibility to take precautions such as those described below to protect yourselfagainst the above network security risks.Use this unit in a network secured by a firewall, etc.⿟⿟ If this unit is connected to a network that includes PCs, make sure that the system is not infected by computerviruses or other malicious entities (using a regularly updated anti-virus program, anti-spyware program, etc.).Protect your network against unauthorized access by restricting users to those who log in with⿟an authorized user name and password.Apply measures such as user authentication to protect your network against leakage or theft of⿟information, including image data, authentication information (user names and passwords), alarmmail information, FTP server information and DDNS server information.After the unit is accessed by the administrator, make sure to close the browser.⿟Change the administrator password periodically.⿟Do not install the camera in locations where the camera or the cables can be destroyed or dam-⿟aged by persons with malicious intent.Before asking for repairs, check the symptoms with the following table.Contact your dealer if a problem cannot be solved even after checking and trying the solution in thetable or a problem is not described below.Symptom Cause/solutionPower is not turned on. uAre the PoE device and the network cable of the camera⿟connected using a LAN cable? Check whether the connection is appropriately established.Depending on the PoE device, the power supply will stop⿟when the demanded power exceeds its total power limit forall PoE ports. Refer to the operating instructions of the PoE device in use.Distributing, copying, disassembling, reverse compiling and reverse engineering of the software pro-vided with this product are all expressly prohibited. In addition, exporting any software provided withthis product violating export laws is prohibited.PrecautionsSpecificationsLimitation of liabilityDisclaimer of warrantyCopyright● BasicPower source: PoE (IEEE802.3af compliant), 12 V DCPower consumption: PoE: 130 mA (Class 2 device), 12 V DC: 430 mAAmbient operating temperature: -20 °C to +50 °C {-4 °F to 122 °F}Ambient operating humidity: Less than 90 % (no condensation)Monitor output: VBS: 1.0 V [p-p]/75 Ω, composite (BNC), ø3.5 mm mini jackEXT I/O terminal cable: ALARM IN 1, ALARM IN 2/ ALARM OUT, ALARM IN 3/ AUX OUT, GND, 12 V DCMicrophone/Line input:For microphone inputFor line inputø3.5 mm monaural mini jackInput impedance: Approx. 2.2 kΩApplicable microphone: Plug-in power typeSupply voltage: 3.3 V ±0.5 VInput level: Approx. –10 dBVAudio output: ø3.5 mm stereo mini jack (monaural output)Output impedance: Approx. 560 ΩLine levelDustproof/ Waterproof: IP55** Only when installation work specified in this book is properly per-formed and appropriate waterproof treatment is performedDimensions: 100 mm (W) x 100 mm (H) x 74 mm (D) {3-47/50 inches (W) x 3-47/50inches (H) x 2-23/25 inches (D)} (excluding projection)Mass: Main body: 350 g {0.77 lbs}Finish: Main body : PC/ABS resin, silverDome section: Clear polycarbonate resin● CameraImage sensor: 1/4 type MOS image sensorEffective pixels: Approx. 1.3 megapixelsScanning area: 3.52 mm (H) × 2.64 mm (V) {7/50 inches (H) × 1/10 inches (V)}Scanning system: ProgressiveMinimum illumination: Color: 0.6 lx {0.06 footcandle}(F2.2, Auto slow shutter: Off (1/30 s), Gain: On (High))0.038 lx {0.0038 footcandle}(F2.2, Auto slow shutter: max. 16/30 s, Gain: On (High))*BW: 0.5 lx {0.05 footcandle}(F2.2, Auto slow shutter: Off (1/30 s), Gain: On (High))0.031 lx {0.0031 footcandle}(F2.2, Auto slow shutter: max. 16/30 s, Gain: On (High))** Converted valueWide dynamic range: On/OffFace WDR: On/OffGain (AGC): On (Low)/ On (Mid)/ On (High)/ OffAdaptive black stretch: On/OffLight control mode setting: Indoor scene (50Hz/60Hz)/ELCELC(Maximum exposure time):ELC(1/30 s), ELC(3/100 s), ELC(3/120 s), ELC(2/100 s), ELC(2/120 s),ELC(1/100 s), ELC(1/120 s), ELC(1/250 s), ELC(1/500 s),ELC(1/1000 s), ELC(1/2000 s), ELC(1/4000 s), ELC(1/10000 s)Auto slow shutter: Off (1/30 s), Max. 2/30s, Max. 4/30s, Max. 6/30s, Max. 10/30s,Max. 16/30sDay & Night (electrical): Off/AutoWhite balance: ATW1/ ATW2/ AWCDigital noise reduction: High/LowVideo analyticsFace detection:On/Off (with the XML notification setting)Privacy zone: On/Off (up to 2 zones available)Camera title on screen: Up to 20 characters (alphanumeric characters, marks), On/OffVideo motion detection (VMD alarm): On/Off, (available at each preset)● LensZoom ratio: Extra zoom: 2x (under VGA resolution)Digital (electronic) zoom: 8x (Max 16x combined with Extra Optical Zoom under VGA)Focal length: 1.95 mmMaximum aperture ratio: 1: 2.2Focus range: ∞ - 0.5 mAngular field of view: Horizontal: 85°, Vertical: 68°● Panning/tilting platformPanning range: -47.5°- +47.5°Panning speed: Manual: Approx. 5 °/s - 80 °/s, Preset: Up to approx. 80 °/sTilting range: -45° to +10°Tilting speed: Manual: Approx. 5 °/s - 80 °/s, Preset: Up to approx. 80 °/sNumber of the preset positions: 64Map shot: Preset map-shotSelf return: 10 s/ 20 s/ 30 s/ 1 min/ 2 min/ 3 min/ 5 min/ 10 min/ 20 min/ 30 min/ 60 minNetwork securityWARNINGCAUTIONTurn the power off when cleaning this product.• Failure to observe this may cause injury.Refer installation work to the dealer.• Installation work requires technique and experiences. Failure to observe this may cause fire,electric shock, injury, or damage to the product.Be sure to consult the dealer.•Stop the operation immediately when something is wrong with this product.• When smoke goes up from the product, the smell of smoke comes from the product, or theexterior of the product has deteriorated, continued use will cause a fire or fall of the productresulting in injury, or damage to the product.Turn the power off immediately and contact qualified service personnel for service.•Select an installation area that can support the total weight.• Selecting an inappropriate installation surface may cause this product to fall down or toppleover, resulting in injury.Installation work shall be started after sufficient reinforcement.•Periodic inspections shall be conducted.• Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.Consult the dealer for the inspections.•The screws and bolts must be tightened to the specified torque.• Failure to observe this may cause a drop resulting in injury or accidents.Do not install this product in locations subject to vibration.• Loosening of mounting screws or bolts may cause a fall of the product resulting in injury.The measures of protection against a fall of this product shall be taken.• Failure to observe this may cause a drop resulting in injury or accidents. Be sure to install the safety wire.Install this product in a location high enough to avoid people and objects from• bumping the product.Failure to observe this may cause a drop resulting in injury or accidents.Turn the power off when do wiring of this product.• Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring maycause fire.Do not attempt to disassemble or modify this product.• Failure to observe this may cause fire or electric shock. Consult the dealer for the repair orinspections.Do not insert any foreign objects.• This could permanently damage this product. Turn the power off immediately and contactqualified service personnel for service.Do not use this product in an inflammable atmosphere.• Failure to observe this may cause an explosion resulting in injury.Avoid installing this product in the locations where salt damage occurs or• corrosive gas is produced.Otherwise, the mounting portions will deteriorate and accidents such as a fall of the product may occur.Do not strike or give a strong shock to this product.• Failure to observe this may cause fire or injury.Do not rub the edges of metal parts with your hand.• Failure to observe this may cause injury.Do not touch this product or the connected cables during thunder. (even in the• process of work)Failure to observe this may cause electric shock.Keep SDHC/SD memory cards (option) away from infants and children.• Otherwise, they may swallow the cards by mistake.In this case, consult a doctor immediately.•● NetworkNetwork: 10BASE-T/100BASE-TX, RJ45 connectorResolution: WV-SW175:Imaging mode: 4:3H.264 1280x960/ VGA (640x480)/ QVGA (320x240) max.30fpsJPEG 1280x960/ VGA (640x480)/ QVGA (320x240) max.30 fpsImaging mode: 16:9H.264 1280x720/ 640x360/ 320x180 max.30 fpsJPEG 1280x720/ 640x360/ 320x180 max.30 fpsWV-SW172:Aspect ratio: 4:3H.264 SVGA(800x600)/ VGA(640x480)/ QVGA(320x240) max. 30 fpsJPEG SVGA(800x600)/ VGA(640x480)/ QVGA(320x240) max. 30 fpsAspect ratio: 16:9H.264 640x360/ 320x180, max. 30 fpsJPEG 640x360/ 320x180, max. 30 fpsImage compressionmethod:*1H.264 Image quality: Low/ Normal/ FineTransmission type: Unicast/MulticastBit rate:Constant bit rate/ Best effort:64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/768 kbps/ 1024 kbps/ 1536 kbps/ 2048 kbps/ 3072 kbps/4096 kbps/ 8192 kbpsFrame rate:1 fps/ 3 fps/ 5 fps/ 7.5 fps/ 10 fps/ 12 fps/ 15 fps/ 20 fps/30 fpsJPEG Image quality: 0 SUPER FINE/ 1 FINE/ 2/ 3/ 4/ 5 NORMAL/6/ 7/ 8/ 9 LOW (10 steps: 0-9)Transmission type: PULL/PUSHTransmission interval: 0.1 fps - 30 fps (JPEG frame rate will be restricted when displayingboth JPEG and H.264/ images.)Audio compressionmethod:G.726 (ADPCM) 32 kbps/ 16 kbpsG.711 64 kbpsBandwidth control: Unlimited/ 64 kbps/ 128 kbps/ 256 kbps/ 384 kbps/ 512 kbps/768 kbps/ 1024 kbps/ 2048 kbps/ 4096 kbps/ 8192 kbpsProtocol: IPv6: TCP/IP, UDP/IP, HTTP, HTTPS, RTP, FTP, SMTP, DNS, NTP,SNMP, DHCPv6, MLD, ICMP, ARPIPv4: TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, SMTP,DHCP, DNS, DDNS, NTP, SNMP, UPnP, IGMP, ICMP, ARPMaximum concurrentaccess number:14 (Depends on network conditions)FTP client: Alarm image transmission, FTP periodic transmissionMulti-screen: Up to 16 camera images can be displayed simultaneously on a multi-screen. (Including the camera itself)Compatible SDHC/SD memory card (option):Manufactured by PanasonicSDHC memory card: 4 GB, 8 GB, 16 GB, 32 GBSD memory card: 256 MB, 512 MB, 1 GB, 2 GB(except miniSD card and microSD card)Cellular phonecompatibility:JPEG image, panning/tilting/zoom control, AUX control (by accesslevel)Mobile terminal compatibility: iPad, iPhone, iPod touch (iOS 4.2.1 or later) (As of August, 2011)*1 Transmission for 2 streams can be individually set in the same compression method.● Optional accessoriesUser License Accessory (For H.264) BB-HCA8A (P model)BB-HCA8CE (E model, Korea*) * Required in KoreaTroubleshootingImportant safety instructions1) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.6) Do not install near any heat sources such as radiators, heat registers, stoves, or other appara-tus (including amplifiers) that produce heat.7) Only use attachments/accessories specified by the manufacturer.8) Use only with the cart, stand, tripod, bracket, or table specified by themanufacturer, or sold with the apparatus. When a cart is used, usecaution when moving the cart/apparatus combination to avoid injuryfrom tip-over.S3125A9) Unplug this apparatus during lightning storms or when unused for long periods of time.10) Refer all servicing to qualified service personnel. Servicing is required when the apparatus hasbeen damaged in any way, such as power-supply cord or plug is damaged, liquid has beenspilled or objects have fallen into the apparatus, the apparatus has been exposed to rain ormoisture, does not operate normally, or has been dropped.THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHEREXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OFMERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT OFTHE THIRD PARTY’S RIGHT.THIS PUBLICATION COULD INCLUDE TECHNICAL INACCURACIES OR TYPOGRAPHICALERRORS. CHANGES ARE ADDED TO THE INFORMATION HEREIN, AT ANY TIME, FOR THEIMPROVEMENTS OF THIS PUBLICATION AND/OR THE CORRESPONDING PRODUCT (S).IN NO EVENT SHALL Panasonic System Networks Co., Ltd. BE LIABLE TO ANY PARTY OR ANYPERSON, EXCEPT FOR REPLACEMENT OR REASONABLE MAINTENANCE OF THE PRODUCT,FOR THE CASES, INCLUDING BUT NOT LIMITED TO BELOW:(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT LIMITATION, DIRECT OR INDIRECT, SPECIAL,CONSEQUENTIAL OR EXEMPLARY, ARISING OUT OF OR RELATING TO THE PRODUCT;(2) PERSONAL INJURY OR ANY DAMAGE CAUSED BY INAPPROPRIATE USE OR NEGLIGENTOPERATION OF THE USER;(3) ALL MALFUNCTIONS OR TROUBLES FROM UNAUTHORIZED DISASSEMBLE, REPAIR ORMODIFICATION OF THE PRODUCT BY THE USER, REGARDLESS OF THE CAUSE OF THEMALFUNCTION OR TROUBLE;(4) INCONVENIENCE OR ANY LOSS ARISING WHEN IMAGES ARE NOT DISPLAYED, DUE TOANY REASON OR CAUSE INCLUDING ANY FAILURE OR PROBLEM OF THE PRODUCT;(5) ANY PROBLEM, CONSEQUENTIAL INCONVENIENCE, OR LOSS OR DAMAGE, ARISINGOUT OF THE SYSTEM COMBINED BY THE DEVICES OF THIRD PARTY;(6) ANY CLAIM OR ACTION FOR DAMAGES, BROUGHT BY ANY PERSON OR ORGANIZATIONBEING A PHOTOGENIC SUBJECT, DUE TO VIOLATION OF PRIVACY WITH THE RESULT OFTHAT SURVEILLANCE-CAMERA’S PICTURE, INCLUDING SAVED DATA, FOR SOMEREASON, BECOMES PUBLIC OR IS USED FOR ANY PURPOSE;(7) LOSS OF REGISTERED DATA CAUSED BY ANY FAILURE.For U.S. and Canada:Panasonic System CommunicationsCompany of North America,Unit of Panasonic Corporation of North Americawww.panasonic.com/business/For customer support, call 1.800.528.6747Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A.Panasonic Canada Inc.5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada(905)624-5010www.panasonic.ca© Panasonic System Networks Co., Ltd. 2011For Europe and other countries:http://panasonic.netImporter’s name and address to follow EU rules:Panasonic Testing CentrePanasonic Marketing Europe GmbHWinsbergring 15, 22525 Hamburg F.R.GermanyWARNING:To prevent injury, this apparatus must be securely attached to the floor/wall/ceiling in accor-⿟dance with the installation instructions.The installation shall be carried out in accordance with all applicable installation rules.⿟The connections should comply with local electrical code.⿟For U.S.AThis product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material - spe-cial handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate/For U.S. and Canada: WV-SW175/WV-SW172For Europe and other countries: WV-SW175E/WV-SW172EFor CanadaThis Class A digital apparatus complies with Canadian ICES-003.For U.S.ANOTE: This equipment has been tested and found to comply with the limits for a Class A digitaldevice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonableprotection against harmful interference when the equipment is operated in a commercial environ-ment. This equipment generates, uses, and can radiate radio frequency energy and, if notinstalled and used in accordance with the instruction manual, may cause harmful interference toradio communications. Operation of this equipment in a residential area is likely to cause harmfulinterference in which case the user will be required to correct the interference at his own expense.FCC Caution: To assure continued compliance, (example - use only shielded interface cableswhen connecting to computer or peripheral devices). Any changes or modifications not express-ly approved by the party responsible for compliance could void the user’s authority to operatethis equipment.For U.S.AThe model number and serial number of this product may be found on the surface of the unit.You should note the model number and serial number of this unit in the space provided andretain this book as a permanent record of your purchase to aid identification in the event of theft.Model No. _________________________________Serial No. __________________________________For EuropeWe declare under our sole responsibility that the product to which this declaration relates is inconformity with the standard or other normative document following the provisions of Directive2004/108/EC.Wir erklären in alleiniger Verantwortung, daß das Produkt, auf das sich diese Erklärung bezieht,mit der folgenden Norm oder normativen Dokument übereinstimmt. Gemäß den Bestimmungender Richtlinie 2004/108/EC.Nous déclarons sous notre propre responsabilité que le produit auquel se réfère la présentedéclaration est conforme á la norme spécifiée ou à tout autre document normatif conformémentaux dispositions de la directive 2004/108/CE.Nosotros declaramos bajo nuestra única responsabilidad que el producto a que hace referenciaesta declaración está conforme con la norma u otro documento normativo siguiendo las estipu-laciones de la directiva 2004/108/CE.Noi dichiariamo sotto nostra esclusiva responsabilità che il prodotto a cui si riferisce la presentedichiarazione risulta conforme al seguente standard o altro documento normativo conforme alledisposizioni della direttiva 2004/108/CE.Wij verklaren als enige aansprakelijke, dat het product waarop deze verklaring betrekking heeft,voldoet aan de volgende norm of ander normatief dokument, overeenkomstig de bepalingen vanRichtlijn 2004/108/EC.Vi erklærer os eneansvarlige for, at dette produkt, som denne deklaration omhandler, er i over-ensstemmelse med standard eller andre normative dokumenter i følgebestemmelserne i direktiv2004/108/EC.Vi deklarerar härmed vårt fulla ansvar för att den produkt till vilken denna deklaration hänvisar är iöverensstämmelse med standarddokument eller annat normativt dokument som framställs idirektiv 2004/108/EC.Ilmoitamme yksinomaisella vastuullamme, että tuote, jota tämä ilmoitus koskee, noudattaaseuraavaa standardia tai muuta ohjeellista asiakirjaa, jotka noudattavat direktiivin 2004/108/ECsäädöksiä.Vi erklærer oss alene ansvarlige for at produktet som denne erklæringen gjelder for, er i overens-stemmelse med følgende norm eller andre normgivende dokumenter som følger bestemmelsenei direktiv 2004/108/EC.Information for Users on Collection and Disposal of Old Equipment and used BatteriesThese symbols on the products, packaging, and/or accompanying documents meanthat used electrical and electronic products and batteries should not be mixed withgeneral household waste.For proper treatment, recovery and recycling of old products and used batteries,please take them to applicable collection points, in accordance with your national leg-islation and the Directives 2002/96/EC and 2006/66/EC.By disposing of these products and batteries correctly, you will help to save valuableresources and prevent any potential negative effects on human health and the envi-ronment which could otherwise arise from inappropriate waste handling.For more information about collection and recycling of old products and batteries,please contact your local municipality, your waste disposal service or the point of salewhere you purchased the items.Penalties may be applicable for incorrect disposal of this waste, in accordance withnational legislation.For business users in the European UnionIf you wish to discard electrical and electronic equipment, please contact your dealeror supplier for further information.Cd[Information on Disposal in other Countries outside the European Union]These symbols are only valid in the European Union. If you wish to discard theseitems, please contact your local authorities or dealer and ask for the correct methodof disposal.Note for the battery symbol (bottom two symbol examples):This symbol might be used in combination with a chemical symbol. In this case itcomplies with the requirement set by the Directive for the chemical involved.About the user manualsThere are 2 sets of operating instructions for the WV-SW175, WV-SW172 (P model), WV-SW175E,WV-SW172E (E model) as follows.Installation Guide: Explains how to install and connect devices, as well as how to connect and⿟configure the network.Operating Instructions (included in the CD-ROM): Explains how to perform the settings and how⿟to operate this camera.Adobe® Reader® is required to read these operating instructions on the provided CD-ROM.When the Adobe ® Reader® is not installed on the PC, download the latest Adobe Reader from theAdobe web site and install it.“WV-SW175, WV-SW172” or “SW175, SW172” shown in the instructions and illustrations used inthese operating instructions indicates the WV-SW175, WV-SW172, WV-SW175E, WV-SW172E.The screens used in these operating instructions show the cases of P models.

/ 2

Related manuals for Panasonic WV-SW172