Panasonic WV-Q160C Operating Instructions Manual

Also see for WV-Q160C: Operating instructions

Panasonic WV-Q160C Operating Instructions Manual Manual pdf 1 page image

PrefaceThis ceiling mount bracket is exclusively designed to mount the network camera. Refer to the catalog orthe installation guide of the camera for supported cameras.• WV-Q160C: Clear dome cover• WV-Q160S: Smoked dome cover (approx. 50 % of transmittance)Precautions• Use only the specified camera.Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents.Refer to the catalog or the installation guide of the camera for supported cameras• Avoid installing this bracket in the locations where salt damage occurs or corrosive gas isproduced.Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera mayoccur.• Refer installation work to the dealer.Installation work requires technique and experience. Failure to observe this may cause fire, electricshock, injury, or damage to the product. Be sure to consult the dealer.• Do not install this product in locations subject to vibration.Loosening of mounting screws or bolts may cause'a fall of the product resulting in injury or acci-dents.• Install this product in a location high enough to avoid people and objects from bumpingthe product.Failure to observe this may cause injury.• The measures of protection against a fall of the camera shall be taken.Failure to observe this may cause a drop resulting in injury. Be sure to install this bracket-specificsafety wire.• Periodic inspections shall be conducted.Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult thedealer for the inspections.Parts and functionsNote:• Remove the notch with a nipper.• If a tiepin type microphone is used, mount the microphone on the rubber-made microphone stand.Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.Important: In order to avoid injury and to protect the cable, file the edge of the notch.LOCKOPENNotch for network cable,monitor output cable, etc.Dome coverCeiling mount bracketHole for microphone cableMicrophone stand*InstallationsBe sure to read "Precautions" before installation. TheInstallation Guide of the network camera shall be readas well.1. Install the inner cover.Slide the covers located on the both lateral sidesof the camera and put the inner cover on thecamera until the hooks inside the inner cover areheld in the holes of the camera (until a click isheard).Important: Put the inner cover down on the cam-era until the outside cover of the camera can-not be seen from the opening (from which thecamera lens is visible) of the inner cover. If thisintegration is not successfully performed, theinner cover may be removed or the hidden partat the top of the screen may become larger inthe WIDE mode.CoverHookPut on until a click isheardInner coverHow to remove the inner coverPress the inner cover from the front and rearsides inward (at the same vertical position asthe hooks) to bend the cover and remove thecover from the camera.Press from the front and rearsides inward to bend(To be continued reverse page)Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.The model number is abbreviated in some descriptions in this manual.Operating InstructionsCeiling Mount BracketModel No. WV-Q160CWV-Q160SNs0817-0 PGQX2212ZA Printed in ChinaPrecaution for installationThis product is designed to be used indoors. This product is not operable outdoors.In order to prevent injury, the product must be securely mounted to a ceiling according toInstallation Guide.• Make sure that the installation area is strong enough to hold the total weight of the camera assem-bly (approx. 1.4 kg {3.1 lbs.}) before installation.• The screws that secure the ceiling mount bracket (provided with the camera) in the ceiling are notsupplied. Prepare them according to the material and strength of the area where the product is tobe installed. In this case, wood screws and nails should not be used.• Do not place this product in the following places.• Locations where a chemical agent is used such as a swimming pool• Locations subject to moisture or oil smoke such as a kitchen• Locations that have a specific environment that is subject to an inflammable atmosphere or sol-vents• Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated• Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gasessuch as from hot springs, volcanic regions, etc.• Locations where the temperature is not within –10 °C - +50 °C {14 °F - 122 °F}.• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (Thisproduct is not designed for on-vehicle use.)• Locations where it may get wet from rain or water splash (including under the eaves, etc.)• Locations subject to moisture or dust• Locations subject to condensation as the result of severe changes in temperature (In case ofinstalling the product in such locations, the front cover may become foggy or condensation maybe caused on the cover.)• The screws and bolts must be tightened with an appropriate tightening torque according to thematerial and strength of the installation area. After tightening the screws or bolts, perform visualcheck to ensure tightening is enough and there is no backlash.• The pull-out strength of the installation area shall be 196 N {44 lbf} or more per 1 screw.2. Mount the camera.The camera shall be mounted on the camera mounting bracket (supplied with the camera) aftermounting this bracket on a ceiling.For further information, refer to the Installation Guide of the network camera.

/ 2

Related manuals for Panasonic WV-Q160C