Panasonic WV-CW374 Instruction Manual

Also see for WV-CW374: Brochure & specs Operating instructions

Panasonic WV-CW374 Instruction Manual Manual pdf 1 page image

Fixing the camera, camera mounting arm, and adapter boxAs the factory default, the camera head has been tilted to the downside.1. Move the camera head, as shown in the illustrations, by loosening the tilting lock screw.2. After adjustment, tighten the tilting lock screw again.3. Attach the camera mounting arm to the left or right hinges of adapter box, so that the mountingarm can be opened and closed flexibly. (Refer to the illustration in Step 4.)Note: Attach the mounting arm to hinges on the side opposite to the wall.4. Fix the camera to the camera mounting arm.Note: Lead the camera cables out of the cable hole of mounting arm.5. Pass the cables through the cable clamp of mounting arm, and then to the wall.Note: Do not expose the cables to sunlight. Fixing the Mounting Arm DirectlyNotes:• For outdoor use, the mounting screws and screw holes require waterproofing. Refer toWaterproof Process in this document.• Avoid waterproofing the drainage hole.With the mounting screws (locally procured), fix the camera mounting arm directly to a wall or ajunction box installed on the wall.Tilting lock screw(Hexagon socket screw)Camera headSDIIWV-CW374CameraFixing screws for camera(Supplied) x 3(M4 x 8)Mounting armAdapter boxHingesFixing screw for adapter box(Supplied) x1(M4 x 35)Cable clampMounting screws(Locally procured) x 446 mm {1-13/16"}83.5 mm{3-5/16"}Cable access holeSDIIWV-CW374Mounting armHole6 mm (W) x 10 mm (H){1/4" (W) x 13/32" (H)}24.5 mm{31/32"}Mounting armDrainage holeTo facilitate wirings, it is recommended to align two junction boxes. Waterproof ProcessApply waterproofing to the necessary portions, using appropriate materials.This camera is applied to IP66 only when installed according to the instructions in this document,and appropriate waterproofing is applied.Screw-holes, cable access holes, and gaps:Fill these portions with silicon rubber or equivalent waterproofing material.Note: The waterproof process should be made by qualified service personnel or system installersaccording to the local requirement. Fixing the Camera Mounting Arm and Adapter Box1. Fix the camera mounting arm to the adapter box with four supplied screws.2. Fix the mounting arm covers to the mounting arm with two supplied screws. Adjusting the Camera Angle1. Remove the rear cover by loosening the fixing screw.SDIIWV-CW374Covers x 2Fixing screws for covers(Supplied) x 2 (M3 x 6)Fixing screws for adapter box andmounting arm (Supplied) x 4 (M5 x 20)Adapter boxMounting arm(1) Remove the fixing screw.(2) Remove the rear cover.CAUTION(2) Remove the switch cover.(1) Remove the fixing screw. (x 2)2. Remove the switch cover by loosening the two fixing screws.The switch unit will appear.46 mm {1-13/16"}83.5 mm{3-5/16"}Mounting screws(Locally procured) x 4SDIIWV-CW374JunctionboxMounting armHole6 mm (W) x 10 mm (H){1/4" (W) x 13/32" (H)}Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.N0504-0 3TR002485AAA Printed in Japan PrefacePanasonic WV-CW374 is designed for installation on the wall, using a camera mounting arm or thesupplied adapter box. Precautions• Refer all work related to the installation of this product to qualified service personnel orsystem installers.• Do not operate the appliance beyond its specified temperature, humidity, or powersource ratings.Use the camera at temperatures between –30 °C and +50 °C {between –22 °F and 122 °F}, andhumidity below 90 %. The input power source for this appliance is 12 V DC/24V AC 60 Hz forWV-CW374.When you install the camera in a low-temperature location and start operating it, it may taketime (around 30 minutes) for the inside of the camera to warm up. Cut power once then supplypower again.• Screws to mount the camera is not supplied.Prepare locally procured screws matching the material, structure, and total weight of mountingplace.• Be sure to use a ceiling board having enough strength to support this camera.WARNING: All work related to the installation of this product should be made by qualified service personnel or sys-tem installers.CAUTION: An ALL-POLE MAINS SWITCH with a contact separation of at least 3 mm {0.12"} in each pole shall beincorporated in the electrical installation of the building. PreparationsThe camera can be mounted either of the following ways.• Using the supplied adapter box.• Fixing the camera mounting arm directlyCaution: When installing, the power cord is NOT to be exposed to outdoor conditions like frost andsunlight.Using the supplied adapter boxWhen you mount the camera on a flat wall with a cable access hole, or through exposed wirings,you will use the supplied adapter box. For installation, refer to Installation of Camera and AdapterBox.Notes:• Mounting screws are not supplied. Prepare locally procured screws matching the material,structure, and total weight of mounting place.• Screws to fix the camera mounting arm to the adapter box are supplied.Fixing the supplied camera mounting arm directly• You can fix the camera mounting arm to a junction box installed on the wall.• You can fix the camera mounting arm directly to the wall with a cable access hole.For installation, refer to Fixing the Mounting Arm Directly.Note: Mounting screws are not supplied. Prepare locally procured screws matching the material,structure, and total weight of mounting place. Installation of Camera and Adapter BoxNotes:• For outdoor use, the mounting screws and screw holes require waterproofing. Refer toWaterproofing Process in this document.• When wiring the camera cables through the adapter box, use a cable access hole. The cableaccess hole is G3/4.Installing the adapter box directly to the wallWith the mounting screws (locally procured), fix the adapter box to a junction box or directly to thewall.Installing the adapter box to a junction boxTo facilitate wirings, it is recommended to align two junction boxes.Color CCTV CameraInstructionsModel No. WV-CW374The serial number of this product may be found onthe top of the unit.You should note the serial number of this unit in thespace provided and retain this instruction as a per-manent record of your purchase to aid identificationin the event of theft.Model No.Serial No.46 mm {1-13/16”}22 mm{14/16"}83.5 mm{3-5/16"}24.5 mm{31/32"}Hole6 mm (W) x 10 mm (H){1/4” (W) x 13/32” (H)}Cable access hole(Used for wiring)(G3/4" internal thread)Mounting screws(Locally procured) x 4Center ofadapter boxCable access holeAdapter box46 mm {1-13/16"}83.5mm{3-5/16"}Mounting screws(Locally procured) x 4Junction boxHole6 mm (W) x 10 mm (H){1/4" (W) x 13/32" (H)}SDIIWV-CW374The exclamation point within anequilateral triangle is intended toalert the user to the presence ofimportant operating and mainte-nance (servicing) instructions in theliterature accompanying the appli-ance.The lightning flash with arrowheadsymbol, within an equilateral trian-gle, is interned to alert the user tothe presence of uninsulated "dan-gerous voltage" within the product'senclosure that may be of sufficientmagnitude to constitute a risk ofelectric shock to persons.SA 1966SA 1965CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE. REFER SER-VICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRICSHOCK DO NOT OPENNOTE: This equipment has been tested and foundto comply with the limits for a Class A digitaldevice, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonableprotection against harmful interference when theequipment is operated in a commercial environ-ment. This equipment generates, uses, and canradiate radio frequency energy and, if not installedand used in accordance with the instruction manu-al, may cause harmful interference to radio com-munications.Operation of this equipment in a residential area islikely to cause harmful interference in which casethe user will be required to correct the interferenceat his own expense.FCC Caution: To assure continued compliance,(example - use only shielded interface cables whenconnecting to computer or peripheral devices). Anychanges or modifications not expressly approvedby the party responsible for compliance could voidthe user’s authority to operate this equipment.For U.S.ACaution:Before attempting to connect or operate thisproduct, please read the marking on the top.

/ 2

Related manuals for Panasonic WV-CW374