Panasonic WV-CP240 Operating Instructions Manual

Also see for WV-CP240: Operating instructions Specifications

Panasonic WV-CP240 Operating Instructions Manual Manual pdf 1 page image

Copper wiresize (AWG)Copper wiresize (AWG)Lengthof Cable(Approx.)CONNECTIONSA. WV-CP240 (120V AC 60Hz)Connect the power cord to an electrical outletof 120V AC 60Hz.B. WV-CP242 (12V DC)Connect the power cord to the DC 12V IN ter-minal on the rear panel of the WV-CP242.Resistance of copper wire [at 20°C (68°F)]• Calculation of maximum cable lengthbetween camera and power supply :ResistanceΩ/mResistanceΩ/ft#24(0.22mm 2)0.0780.026#22(0.33mm 2)0.0500.017#20(0.52mm 2)0.03.0.010#18(0.83mm 2)0.0180.00610.5V DC ≤ VA − (R x 0.42 x L) ≤ 16V DCL : Cable length (meters)R : Resistance of copper wire (Ω/meter)VA : DC output voltage of power supply unitVA − 12L standard = (meters)0.42 x RVA − 16L minimum = (meters)0.42 x RVA − 10.5L maximum = (meters)0.42 x RThe following adjustment should be made byqualified service personnel or system installers.q Loosen the screw on the side of the camera.w Turn the flange-back adjusting ring to thedesired position.Caution: When the C-mount lens is mounted,do not rotate the ring counterclockwiseby force after it stops. If the ring is rotat-ed by force, the inner lens or CCD imagesensor may be damaged.e Tighten the screw on the side of the camera.Caution: Tightening the screw by force willcause damage to the screw or deviationof focus.FOCUS OR FLANGE-BACK ADJUSTMENT12 V DC(10.5 V - 16 V)@ !C. WV-CP244 (24V AC 60Hz)Connect the power cable to the AC 24 V INterminal on the rear panel of the WV-CP244.(m)(ft)#24(0.22mm2)95314#22(0.33mm 2)150495#20(0.52mm 2)255842#18(0.83mm 2)4251 403Recommended wire gauge sizes for 24 V AC line24 V AC, 60 Hz(19.5 V - 28 V)1 2Installation of Auto Iris LensConnectorInstall the lens connector (YFE4191J100) whenusing a video drive ALC lens.The installation should be made by qualifiedservice personnel or system installers.Cut the iris control cable at the edge of the lensconnector to remove the existing lens connectorand then remove the outer cable cover of the sup-plied connector as shown in the diagram.The pin assignment of the lens connector is as fol-lows:Pin 1: Power source; +9 V DC, 50 mA max.Pin 2: Not usedPin 3: Video signal; 0.7 V[p-p]/40 kΩPin 4: Shield, groundPin 3Pin 4Pin 2RibPin 1Mounting the LensCaution:Before you mount the lens, loosen the screwon the side of the camera, and rotate theflange-back adjusting ring clockwise until itstops. If the ring is not at the end, the innerlens or CCD image sensor may be damaged.q Mount the lens by turning it clockwise on thelens mount of the camera.w Connect the lens cable to the auto iris lensconnector on the side of the camera.Focus Fixing ScrewwqcscCaution for Mounting the LensThe lens mount should be a C-mount or CS-mount(1”-32UN) and the lens weight should be less than450 g (0.99 lbs). If the lens is heavier, both thelens and camera should be secured by using thesupporter.The protrusion at the rear of the lens should be asshown in the diagram.C-mount: Less than 13 mm (1/2”)CS-mount: Less than 8 mm (5/16”)Solder the lens cable to the pins of the sup-plied connector.Flange-backAdjusting RingFocus Fixing ScrewFocusing ofC-mount lensFocusing ofCS-mount lensLOCKCaution:To prevent fire or electric shock hazard, usea UL listed cable (VW-1, style 1007) for theDC 12 V or AC 24 V Input Terminal.Video Cable1. It is recommended to use a monitor whoseresolution is at least equal to that of thecamera.2. The maximum extensible coaxial cablelength between the camera and the moni-tor is shown below.Type of RG-59/U RG-6U RG-11/U RG-15/Ucoaxial cable (3C-2V) (5C-2V) (7C-2V) (10C-2V)Recommended (m) 250 500 600 800maximumcable length (ft) 825 1 650 1 980 2 640Pick-up Device: 768 (H) x 494 (V) pixels, Interline Transfer CCDScanning Area: 4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3”pick-up tube)Synchronization: Internal, Line-locked or Multiplexed vertical drive (VD2),selectableScanning System: 2 : 1 interlaceScanning: 525 lines / 60 fields / 30 framesHorizontal: 15.734 kHzVertical: 59.94 HzHorizontal Resolution: 480 linesVideo Output: 1.0 V[p-p] NTSC composite 75 Ω / BNC connectorSignal-to-Noise Ratio: 50 dB (Equivalent to AGC Off, weight On)Electronic Light Control: Equivalent to continuous variable shutter speed between 1/60 sand 1/15 000 sMinimum Illumination: 0.6 lx (0.06 foot-candle) at F0.75 [equivalent to 2.0 lx (0.2 foot-candle) at F1.4] AGC OnDetail: SHARP or SOFT, selectableLens Mount: C-mount or CS-mount, selectableAmbient Operating Temperature: −10°C - +50°C (14°F - 122°F)Ambient Operating Humidity: Less than 90 %Power Source and WV-CP240: 120 V AC 60 Hz, 3.6 WPower Consumption: WV-CP242: 12 V DC, 270 mAWV-CP244: 24 V AC 60 Hz, 3.3 WDimensions (without lens): 67 mm (W) x 65 mm (H) x 123 mm (D)2-5/8” (W) x 2-9/16” (H) x 4-13/16” (D)Weights (without lens): WV-CP240: 0.48 kg (1.06 lbs)WV-CP242: 0.3 kg (0.66 lbs)WV-CP244: 0.33 kg (0.73 lbs)Weights and dimensions indicated are approximate.Specifications are subject to change without notice.SPECIFICATIONSSTANDARD ACCESSORIESBody Cap............................................................................................1 pc.ALC Lens Connector (YFE4191J100).................................................1 pc.OPTIONAL ACCESSORIESLenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LA210C3, WV-LA408C3, WV-LA908C3,WV-LZ61/10, WV-LZ62/2, WV-LZ62/8, WV-LF4R5C3A, WV-LF9C3A, WV-LFY3C3,WV-LFY45C3, WV-LFY9C3PANASONIC CANADA INC.5770 Ambler Drive, Mississauga,Ontario, L4W 2T3 Canada (905)624-5010PANASONIC SALES COMPANYDIVISION OF MATSUSHITA ELECTRIC OF PUERTO RICO INC.San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina,P.R. 00985 (809)750-4300Panasonic Digital Communications & Security CompanyUnit of Matsushita Electric Corporation of AmericaSecurity Systems Groupwww.panasonic.com/cctvExecutive Office: One Panasonic Way 3E-7, Secaucus, New Jersey 07094Zone OfficeEastern: One Panasonic Way, Secaucus, NJ 07094 (201) 348-7303Central: 1707 N.Randal Road, Elgin, IL 60123 (847) 468-5205Western: 6550 Katella Ave., Cypress, CA 90630 (714) 373-78402003 © Matsushita Electric Industrial Co., Ltd. All rights reserved.1. The following functions are built in.(1) Auto Light Control (ALC)/Electronic LightControl (ELC)(2) Automatic Gain Control (AGC) +15 dBand Automatic Tracing White Balance(ATW)(3) Camera synchronization mode selec-table between internal (INT), Line-locked(LL) for WV-CP240 and WV-CP244 andMultiplexed Vertical Drive (VD2).FEATURES2. Minimum illumination of 0.6 lx (0.06 foot-can-dle) at F0.75 (equivalent to 2.0 lx (0.2 foot-candle) at F1.4)3. Signal-to-noise ratio of 50 dB(Equivalent to AGC Off)4. Horizontal resolution of 480 lines5. Auto iris lens control selectable betweenvideo signal and DC power supply.1. Do not attempt to disassemble the camera.To prevent electric shock, do not removescrews or covers.There are no user serviceable parts inside.Ask a qualified service person for servicing.2. Handle the camera with care.Do not abuse the camera. Avoid striking,shaking, etc. The camera could be damagedby improper handling or storage.3. Do not expose the camera to rain ormoisture, or try to operate it in wet areas.Turn the power off immediately and ask aqualified service person for servicing.Moisture can damage the camera and alsocreate the danger of electric shock.4. Do not use strong or abrasive detergentswhen cleaning the camera body.Use a dry cloth to clean the camera whendirty.In case the dirt is hard to remove, use a milddetergent and wipe gently. Afterwards, wipeoff the remained part of the detergent in itwith a dry cloth.5. Clean the CCD faceplate with care.Do not clean the CCD with strong or abrasivedetergents. Use lens tissue or a cotton tippedapplicator and ethanol.6. Never face the camera towards the sun.Do not aim the camera at bright objects.PRECAUTIONSCaution:To prevent fire or electric shock hazard, usea UL listed cable (VW-1, style 1007) for theDC 12 V or AC 24 V Input Terminal.Cautions:• Connect to 12 V DC (10.5 V-16 V) or 24 VAC (19.5 V-28 V) class 2 power supply only.Make sure to connect the grounding lead tothe GND terminal when the power is sup-plied from a 24 V AC power source.• To prevent fire or electric shock hazard, usea UL listed cable (VW-1, style 1007) for theDC 12 V or AC 24 V Input Terminal.GNDAC 24V IN1 2VIDEO OUTVIDEO OUTVIDEO OUT

DC 12V INWV– CP244LLINTELCALCSOFTSHARPOFFBLC ONDCVIDEOELCALCSOFTSHARPOFFBLC ONDCVIDEOLLINTELCALCSOFTSHARPOFFBLC ONDCVIDEOLLINTELCALCSOFTSHARPOFFBLC ONDCVIDEOELCALCSOFTSHARPOFFBLC ONDCVIDEOLOCKFixing ScrewsCamera MountingScrew HolesMount AdaptercscMAJOR OPERATING CONTROLS AND THEIR FUNCTIONSq Auto Iris Lens ConnectorSupplies power and control signals to an autoiris lens (not supplied).w Flange-back Adjusting RingThis ring adjusts the back-focal distance orpicture focus. Rotate this ring clockwise for aC-mount lens or counterclockwise for a CS-mount lens.e Lens (option)r Mount AdapterThe camera mounting screw hole is formounting the camera onto a mounting brack-et. The camera is originally designed to bemounted from the bottom, however, a top-mounting type is also available. To mountfrom the top, remove the mount adapter fromthe bottom of the camera by removing twofixing screws. Attach the mount adapter tothe top as shown in the diagram, then mountthe camera on the mounting bracket. Makesure that two original screws are used whenmounting the mount adapter; longer typescrews may damage inner components, tooshorter type screws may cause the cameradrop.t Focus Fixing Screwy Power Cord (only for WV-CP240)Connect this power cord to an electrical out-let of 120 V AC 60 Hz.u DC 12 V Input Terminal[DC 12V IN (only for WV-CP242)]This terminal is for connecting the 12 V DCpower supply cord.i AC 24 V Input Terminal[AC 24V IN (only for WV-CP244)]This terminal is for connecting the 24 V AC60Hz power supply cord.o Synchronization Mode Selector[INT, LL (only for WV-CP240 and WV-CP244)]Selects the camera synchronization mode aseither internal sync mode (INT) or line-lockmode (LL).INT: Sets to internal 2:1 interlace.LL: Sets to Line-lock mode.!0 Back Light Compensation Mode Selector(BLC ON, OFF)Lets you select the mode according to theposition of the object and light conditions onthe screen.ON: Select this mode when a strong lightsuch as a spotlight is in the background.OFF: Normal picture.!1 Detail/Aperture Level Selector (SHARP,SOFT)The detail/aperture level can be selected withthis selector. Set it to the desired positionwhile observing the picture on the monitor.SHARP: Normal position.SOFT: Select this position when a QuadSystem is connected to this camera.!2 Automatic Light Control/Electronic LightControl Selector (ALC, ELC)Lets you select the mode according to thelens type used.ALC: Select this mode when an auto iris lens(ALC lens) is used with this camera.ELC: Select this mode when a fixed iris lensor manual iris lens is used with this cam-era.!3 Lens Drive Signal Selector (VIDEO, DC)Lets you select the mode according to thetype of auto iris lens drive signal to be sup-plied to the lens from the auto iris lens con-nector.VIDEO: Select this mode if you are using aauto iris lens that requires a video drivesignal.DC: Select this mode if you are using a autoiris lens that requires a DC drive signal.!4 Video Output Connector (VIDEO OUT)This connector is for connecting with theVIDEO IN connector of the video monitor.Whenever the multiplexed vertical drive (VD2)signal is supplied to this connector, the cam-era synchronization mode is automatically setto Vertical Drive.Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.N0301-3043 V8QA5733DN Printed in JapanN 19Model No. WV-CP240WV-CP242WV-CP244Color CCTV CamerasOperating Instructionscsc(Lens Option)Whether the camera is in use or not, neveraim it at the sun or other extremely brightobjects. Otherwise, blooming or smear maybe caused.7. Do not operate the camera beyond thespecified temperature, humidity or powersource ratings.Use the camera under conditions where tem-perature is between –10°C - +50°C (14°F -122°F), and humidity is below 90 %. Theinput power source is 120 V AC 60 Hz forWV-CP240, 12 V DC for WV-CP242, and 24 VAC 60 Hz for WV-CP244.PREFACEPanasonic’s WV-CP240/CP242/CP244 series digi-tal signal processing color CCD cameras intro-duce a new level of high picture quality and highresolution through the use of a 1/3-inch interlinetransfer CCD image sensor having 768 horizontalpixels (picture elements), and digital signal pro-cessing LSI’s. This model offers cutting-edgetechnology for advanced video surveillance.The exclamation point within anequilateral triangle is intended toalert the user to the presence ofimportant operating and mainte-nance (servicing) instructions in theliterature accompanying the appli-ance.The lightning flash with arrowheadsymbol, within an equilateral trian-gle, is intended to alert the user tothe presence of uninsulated "dan-gerous voltage" within the product'senclosure that may be of sufficientmagnitude to constitute a risk ofelectric shock to persons. The serial number of this product may be found onthe bottom of the unit.You should note the serial number of this unit in thespace provided and retain this instruction as a per-manent record of your purchase to aid identificationin the event of theft.Model No.Serial No.SA 1966SA 1965WARNING:To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE. REFER SER-VICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRICSHOCK DO NOT OPENNOTE: This equipment has been tested and foundto comply with the limits for a Class A digitaldevice, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonableprotection against harmful interference when theequipment is operated in a commercial environ-ment. This equipment generates, uses, and canradiate radio frequency energy and, if not installedand used in accordance with the instruction manu-al, may cause harmful interference to radio com-munications.Operation of this equipment in a residential area islikely to cause harmful interference in which casethe user will be required to correct the interferenceat his own expense.FCC Caution: To assure continued compliance,(example - use only shielded interface cables whenconnecting to computer or peripheral devices). Anychanges or modifications not expressly approvedby the party responsible for compliance could voidthe user’s authority to operate this equipment.For U.S.A

/ 2

Related manuals for Panasonic WV-CP240