Panasonic WV-CF212 Operating Instructions Manual

Also see for WV-CF212: Operating instructions

Contents

operating instructions

Panasonic WV-CF212 Operating Instructions Manual Manual pdf 1 page image

1. Do not attempt to disassemble the camera.To prevent electric shock, do not removescrews or covers.There are no user-serviceable parts inside.Ask qualified service personnel for servicing.2. Handle the camera with care.Do not abuse the camera. Avoid striking,shaking, etc. The camera could be damagedby improper handling or storage.3. Do not expose the camera to rain ormoisture, or try to operate it in wet areas.Turn the power off immediately and ask quali-fied service personnel for servicing. Moisturecan damage the camera and also create thedanger of electric shock.4. Do not use strong or abrasive detergentswhen cleaning the camera body.Use a dry cloth to clean the camera whendirty.In case the dirt is hard to remove, use a milddetergent and wipe gently. Afterwards, wipeoff the remained part of the detergent in itwith a dry cloth.5. Clean the lens faceplate with care.Do not clean the lens with strong or abrasivedetergents. Use lens tissue or a cotton tippedapplicator and ethanol.6. Never face the camera towards the sun.Do not aim the camera at bright objects.Whether the camera is in use or not, neveraim it at the sun or other extremely brightobjects. Otherwise, blooming or smear maybe caused.7. Do not operate the camera beyond thespecified temperature, humidity or powersource ratings.Use the camera under conditions where tem-perature is between –10 °C to +50 °C (14 °F to122 °F), and humidity is below 90 %. Theinput power source is 12 V DC, 240 mA.8. It is recommended to use a monitor whoseresolution is at least equal to that of thecamera.PRECAUTIONS+12V–+12 V-qwerouiyt AP SoftAP SharpBLC OFFBLC ON ON1 2MAJOR OPERATING CONTROLS AND THEIR FUNCTIONSq Camera Panelw Panning/Tilting/Azimuth TableAdjusts the panning/tilting angle of the cam-era.e Focus LeverFixes the focus position after adjusting.r Zoom LeverFixes the zoom position after adjusting.t Video Output TerminalConnects to the video input connector of amonitor.y DC 12 V Input TerminalConnects to the 12 V DC, 240 mA power sup-ply. Connection should be made in accor-dance with the !/@ signs of PCB.u Back Light Compensation Mode Selector(BLC ON, OFF)ON: Select this when the brightness level ofthe background is higher than the object.OFF: Select this when you can view theobject without backlight.The factory default setting is OFF.i Aperture Level Selector (AP Sharp/Soft)Sharp: Sharpens the image outline.Soft: Softens the image outline.The factory default setting is Sharp.Note: Set the selector to Soft when a quadsystem is connected to this camera.o Video Jack (3.5 diam. mini jack)Connect the LCD monitor and such deviceswith 3.5 diam. 2-pole L-type plug for check-ing images.!0 Panel Cover!0Caution: To prevent fire or electric shock haz-ard, use a UL listed cable (WV-1, style1007) for the DC 12 V Input Terminal.Before attempting to connect or operate this product,please read these instructions carefully and save this manual for future use.Ns0902-0 3TR001242AAA Printed in ChinaModel No. WV-CF212Color CCTV CameraOperating InstructionsPREFACEPanasonic’s WV-CF212 series digital signal pro-cessing color CCD cameras uses a 1/4-inch inter-line transfer CCD image sensor having 768 hori-zontal pixels (picture elements), and digital signalprocessing LSI’s. This model is designed for videosurveillance.INSTALLATIONS46 mm(1.81")83.5 mm (3.29")Front / UpperCable access hole35° 6-ø4.5(0.18")ø130 (5.12")Installation dimensional drawingWARNING• The following installation should be made by qualified service personnel or system installers andshould confirm to all local codes.• Be sure to use a ceiling board/wall having enough strength to support this camera.■ Camera mounting positionNotes:• Remove the panel cover before the mounting procedure. (Refer to Step 1 to 4 of "How to mount thecamera" on the next page.)• Procure four mounting screws locally.To mount the camera on a junction boxNote: If you mount the camera on a junction box, procure one locally that meets the dimensions in the fig-ure below.1. Install the junction box to the wall/ceiling.2. Attach the four mounting screws to the junction box.3. Fix the camera and the junction box. Then, turn the camera clockwise.4. Fasten all the mounting screws.To mount the camera directly on the wall/ceiling1. Cut out the panel according to the concave.(Refer to the figure on the right.)2. Prepare a space, which is ø155 mm (6.1") orlarger, on the wall/ceiling.3. Attach the four mounting screws to thewall/ceiling. (Refer to "Installation dimensionaldrawing".)4. Fix the camera and the wall/ceiling. Then,turn the camera clockwise.5. Fasten all the mounting screws.Camera mounting screw x 4Shown figure is anexample for junction box. 46 mm(1-13/16")83,5 mm(3-5/16")The exclamation point withinan equilateral triangle is intend-ed to alert the user to the pres-ence of important operatingand maintenance (servicing)instructions in the literatureaccompanying the appliance.The lightning flash with arrow-head symbol, within an equilat-eral triangle, is interned to alertthe user to the presence ofuninsulated "dangerous volt-age" within the product's enclo-sure that may be of sufficientmagnitude to constitute a riskof electric shock to persons. The serial number of this product may be foundon the top of the unit.You should note the serial number of this unitin the space provided and retain this instructionas a permanent record of your purchase to aididentification in the event of theft.Model No. WV-CF212Serial No.SA 1966SA 1965WARNING:To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK).NO USER-SERVICEABLE PARTS INSIDE. REFER SER-VICING TO QUALIFIED SERVICE PERSONNEL.CAUTIONRISK OF ELECTRICSHOCK DO NOT OPENNOTE: This equipment has been tested andfound to comply with the limits for a Class Adigital device, pursuant to Part 15 of the FCCRules. These limits are designed to providereasonable protection against harmful interfer-ence when the equipment is operated in acommercial environment. This equipment gen-erates, uses, and can radiate radio frequencyenergy and, if not installed and used in accor-dance with the instruction manual, may causeharmful interference to radio communications.Operation of this equipment in a residentialarea is likely to cause harmful interference inwhich case the user will be required to correctthe interference at his own expense.FCC Caution: To assure continued compli-ance, (example - use only shielded interfacecables when connecting to computer orperipheral devices). Any changes or modifica-tions not expressly approved by the partyresponsible for compliance could void theuser’s authority to operate this equipment.For U.S.A

/ 2

Related manuals for Panasonic WV-CF212