Panasonic Viera TH-P54Z10H Operating Instructions Manual

Panasonic Viera TH-P54Z10H Operating Instructions Manual Manual pdf 30 page image

30How to Use Menu FunctionsMenu Item Adjustments / Configurations (alternatives)PictureViewing ModeBasic picture mode (Dynamic / Normal / Cinema / THX / Game)Dynamic : Provides enhanced picture contrast and sharpness when viewing in a bright roomNormal : Recommended for viewing under normal ambient room lighting conditionsCinema : For watching movies in a darkened room producing a cinema-like pictureTHX : Provides the ultimate image quality and cinematic experience at homeGame : Game playing time is displayed only when connecting a game equipment.Set for each input signal.●Contrast, Brightness,Colour, SharpnessIncreases or decreases the levels of these options according to your personalpreferenceTint With an NTSC signal source connected to the TV, the picture hue can be adjusted to suit your taste.For NTSC or Component / HDMI input signal reception only●Colour Balance Allows you to set the overall colour tone of the picture (Cool / Normal / Warm)Not valid when the viewing mode is set to THX●Channel Colour Set Colour density varying between broadcast channels can be adjusted to three levels for each reception channel.Select the channel you want to adjust and set this function.●Colour Management Automatically adjusts colours to vivid ones (Off / On) Not valid on PC signal●x.v.ColourIncreases the colour gradations (Off / Auto)This is effective when watching HD moving pictures with extended gamut (xvYCC) fromexternal equipment.HDMI input mode or Movie View mode onlyNot valid when the viewing mode is set to THX●●Eco Mode Adjusts picture settings automatically dependent on ambient lighting conditions (Off / On)P-NR Automatically reduces unwanted picture noise and flicker noise in the contoured parts ofa picture (Off / Min / Mid / Max) Not valid on PC signal●3D-COMBOccasionally, whilst viewing still or slow moving pictures, colour patterning may be seen.Set to “On” to display sharper and more accurate colours. (Off / On)For PAL or NTSC signal reception only● Not valid on S-Video, Component, PC, HDMI and SD Card●Multi Window Splits the screen into two windows (p. 21)Advanced Settings Set for colour balance, view and position. (p. 40)Set for colour balance in Normal, Cinema or THX viewing mode.Reset to Defaults Press the OK button to reset the present Picture Menu to the default settings.SoundMode Basic sound mode (Music / Speech) Set for each input signal.●Bass Increases or decreases level to enhance or minimise lower, deeper sound outputTreble Increases or decreases level to enhance or minimise sharper, higher sound outputBalance Adjusts volume level of right and left speakersHeadphone Volume Adjusts the volume of the headphonesSurroundSurround sound settings (Off / V-Audio / V-Audio Surround / V-Audio ProSurround)V-Audio: Provides a dynamic enhancer to simulate improved spatial effectsV-Audio Surround: Provides a dynamic enhancer of width and depth to simulate improved spatial effectsV-Audio ProSurround: Provides a three-dimentional sound space with digital reverb effectsSwitching is also possible by the Surround button on the remote control. (p. 15)●Volume Correction Adjusts volume of individual channel or input modeSpeaker Distanceto WallAdjusts the low frequency sound (Over 30cm / Up to 30cm)Over 30cm: Recommended when the back space between the display unit and wall is over 30 cmUp to 30cm: Recommended when the back space between the display unit and wall is within 30 cm●●MPXSelects stereo / monaural (Mono / Stereo) (p. 55)Normally: Stereo● Stereo signal cannot be received: Mono●M1 / M2: Available while mono signal is transmitted● Analogue TV mode only●Audio PreferenceSelects the initial setting for audio tracks (Auto / MPEG)Auto : Automatically selects the audio tracks if programme has more than two tracks.The priority is given in the following order - Dolby Digital, MPEG.MPEG : The priority is given to MPEG as long as the programme contains MPEG audio.Dolby Digital is the method of coding digital signals developed by Dolby Laboratories.Apart from stereo (2ch) audio, these signals can be multi-channel audio.MPEG is an audio compression method that compresses audio to the smaller sizewithout any considerable loss of audio quality.Digital TV mode only●●●SPDIF SelectionSelects the initial setting for digital audio output signal from DIGITAL AUDIO OUT terminal (Auto / PCM)Auto: Dolby Digital is output as Dolby Digital Bitstream. MPEG is output as PCM.PCM: Dolby Digital is output as PCM. MPEG is output as PCM.Digital TV mode only●MPEG Optical Level You can adjust the audio level of MPEG output from DIGITAL AUDIO OUT terminal as the initial setting.0dB to -12dB in -2dB reductions● Digital TV mode only●HDMI1 / 4 InputSelect to fit the input signal. (Digital / Analogue) (p. 55)Digital: HDMI cable connection Analogue: HDMI-DVI adapter cable connectionHDMI input mode onlyHDMI2 / 3 terminals are for digital signal only.●●Reset to Defaults Press the OK button to reset the present Sound Menu to the default settings.