© Panasonic Corporation 20171006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japanhttp://www.panasonic.comPNQW5442ZA C0917MM1Model No. VL-V591Installation Guide for the Flush Mounted Box and the Power Supply UnitBefore installationImportant:LTo avoid malfunction or communication disturbances, do not install the lobby station in the following locations:– Places where vibration or any other kind of impact occurs.– Places near hydrogen sulfide.LDo not place other devices or obstacles in the area aroundthe main unit shown in the figure.LDo not install the power supply unit in the following places:– Places where the power supply unit may be splashed with water orchemicals.– Places where there is a high concentration of dust, or high humidity.Top viewImage range:960 mm500 mm 87°Installation position of the main unit and camera range5 mm 5 mm15 mm20 cmMainunitInstalling on a vertical flat wallInstalling on a tilted pedestalLDo not install on a pedestal tilted at less than 45°.The camera angle can beadjusted using the cameraangle control lever on therear of the upper cabinet,so that the image range canbe changed. Refer to themain unit’s installation andoperation guide.(Pitch of fixing screw)(Pitch of fixing screw)(Aperture dimension)148 mm136 mm162 mm280 mm326 mm340 mm80 mm340 mmDrilling dimension of wall surface for the flush mounted box Open the knockout holes of the flush mounted box, andput the wires from each room and the door opener, and theDC cable from the power supply unit through the holes.Mount the box in the wall.Knockout holesWallDC cable connected tothe power supply unitWires connected torooms and the dooropenerInstalling the flush mounted box in the wallLPlease read the main unit’s installation and operation guide with this guide before installation.LIf you intend to install the power supply unit later, return it to the box, and keep it until required.Side view when the camera isinstalled lower than the standardposition, and facing upwards at 15°.Example: Installation height is 980 mm.Side view when the camera is facingforwards at 0° (default).Example: Installation height is 1330 mm(standard position).Side view when the camera is installed on a pedestaltilted at 60°, and facing forwards at 0° (default).Example: Installation height is 1100 mm.Side view when the camera is installed on apedestal tilted at 45°, and facing downwards at 5°.Example: Installation height is 1120 mm.1330 mm1810 mmCenter ofmain unit 66° 650 mmImagerange1160 mm500 mmPPPPPP PPPP,PDJHUDQJH&HQWHURIPDLQXQLW1690 mm980 mm710 mm500 mm980 mmImagerangeCenter ofmain unit 66°PPPPPPPPPP,PDJHUDQJH&HQWHURIPDLQXQLWInstalling the power supply unit on the wallA DC cable is not included. You need to prepare one. For details, refer to the wire type and distance section in the mainunit’s installation and operation guide.About the installation locationLThe AC cable plug is used as the main disconnect device.Ensure that the power outlet is installed near the productand is easily accessible.LA readily accessible disconnect device shall beincorporated external to the equipment.– External disconnect device must be certified and have acreepage and clearance distance of 3 mm or more.Precautions for wiringLMake sure that the power supply unit is unplugged beforeperforming any wiring work.LAlways connect AC or DC cables to the appropriateconnector or connection terminal.LTo prevent the DC cable from disconnecting and to preventelectric shock, secure the DC cable using the cable binder(accessory) and attach the cable cover.How to connect the AC cable and DC cable:Connect the power supply unit (accessory), the AC cable(accessory), and a DC cable (locally procured).ABPower Supply Unit (VL-PS241) side: 1 25 mm 2 7 mmLobby Station (VL-V591) side: 1 52 mm or more 2 12 mmFront viewEFG H *1CD*1 Make sure that there are no bare wires exposed outsidethe product.Power supply unit (with cable cover removed)KI JBottom viewTop viewk DC cable binder hole1 Strip the DC cables as follows:DC cable (1, 2)2 Remove the screws (3) and then remove the cablecover (4).3 Connect the AC cable (5) (accessory) to the AC INconnector (9) on the top of the power supply unit. Next,connect the DC cable (7) (locally procured) to the DCOUT terminal (j) on the bottom of the power supplyunit, and then secure the wires by tightening the screws(6).LRecommended torque: 0.45 N·m {4.6 kgf·cm}Insert the cables firmly all the way into theconnector and terminals. If the cables are notinserted all the way, heat may be generated.CAUTION4 Use the cable binder (8) (accessory) to secure the DCcable (7) (double-coated area) to the power supplyunit.5 Make sure to replace the cable cover (4).Wall mountingAttach the power supply unit to the wall securely.1 Screws (accessory) x 2A
