Panasonic VL-SWD501EX Installation Manual

Also see for VL-SWD501EX: Operating instructions Operating instructions

Panasonic VL-SWD501EX Installation Manual Manual pdf 2 page image

Screw AYou can use the [Wide/Zoom settings] setting on the main monitor to select the area thatis visible when a visitor calls; available settings are [Wide], [Zoom], and [All] (entire imagedisplay). (Default setting: [Wide])● The following values are for when the doorphone is installed in the standard position (the centreof the doorphone’s height is approximately 1,450 mm) and at a distance of approximately500 mm from the camera lens.■ Installation height and area visible by the camera lensWhen set to zoomDisplays a portion of the wide image at 2 times the size.● Because a digital zoom is used, the image quality of zoomdisplay is lower than that of wide display or entire image display.Image displayed onmain monitor:● You can use the main monitor’s [Zoom position settings] setting to select the desired areavisible when zooming. Refer to the following and configure the main monitor.Entire image displayThe area above and below the wide image is visible.Important:● On the bottom surface of the doorphone and the mounting base, there are holes to allow waterto drain. Do not cover them up when installing.● When existing wiring (such as chime wires) is used:- It may contain AC voltage that may cause electric shock and/or damage the product.- Never use the following types of wiring. Consult a qualified technician/dealer.VL-V554EX VL-V554UEX1 Attach the mounting base to the wall securely.Mounting base(accessory)Wire (locally procured)Wall83.5 mmScrews (locally procured) × 2● Install the mounting base on a vertical flat wall.1 Install the flush mounting box in thewall.Flush mounting box (accessory)100 mmKnockout hole *1151 mm37 mm*1 Only open the knockout holes asrequired for the wiring.2 Use a hex wrench (accessory) to loosen screw A and remove the front panel of the door-phone.Screw AFront panel2 mm hex wrench(accessory)3 Connect the wires.Terminal for themain monitor<Rear view>Terminals for the electric locks● Recommended torque:0.5 N·m {5.1 kgf·cm}● Maximum torque:0.7 N·m {7.1 kgf·cm}3-1 Loosen the screws.3-2 Push in the wires to the terminal connectors (non-polar), then tighten the screws.4 Attach the doorphone to the mountingbase.Screws (accessory) × 44 Attach the doorphone to the flush mountingbox.Screws (accessory) × 45 Attach the name plate to the doorphone and use screw A to secure the front panel.● Write the name on the name plate as needed.Name plate(accessory)Screw A ● Recommended torque:0.35 N·m {3.6 kgf·cm}Approx. 500Approx. 170°Approx. 2,250Image rangeApprox. 115°Approx. 500Image displayed onmain monitor:Approx. 1,600Approx. 650Approx. 1,450Up and down Left and right (when looking from above)Up Image rangeApprox. 2,050Approx. 500Centre ofdoorphoneApprox. 45°Centre (default)Approx. 45°Approx. 500Image rangeApprox. 1,650DownApprox. 45°Approx. 500Approx. 1,400Image rangeLeftApprox. 1,500Approx. 1,450Approx. 550Approx. 1,450 Approx. 1,250Approx. 400Installing the doorphone■ About the installation location● The device must be installed inside an electrical panel or cabinet.● A readily accessible disconnect device shall be incorporated external to the equipment.■ Precautions for wiring● Make sure you turn off the power at the breaker before performing any wiring work.● Always connect AC or DC cables to the appropriate connection terminals. Incorrectlyconnecting the AC or DC cables may damage the power supply unit.● To prevent the power cables from disconnecting and to prevent electric shock, secure thepower cables using the cable binders (accessory) and attach the cable covers.How to connect the power cable (AC/DC)1 Strip the AC/DC cables as follows:7 mm45 mm cable> cable>25 mm7 mm2 Remove the screws (B) and then removethe cable covers (A).3 Connect the AC/DC cable to the AC INterminal/DC OUT terminal on the top andbottom of the power supply unit, and thensecure the wires by tightening the screws.● Recommended torque:- AC terminal: 0.4 N·m {4.1 kgf·cm}- DC terminal: 0.45 N·m {4.6 kgf·cm} view>AC cable*1DC cableScrews*1Cable binders (accessory)4 Use the cable binders (accessory) tosecure the AC/DC cables (double-coatedarea) to the power supply unit.5 Make sure to replace the cable covers (A).Connect the power supply unit (accessory) and AC/DC cables (locally procured).CAUTIONInsert the cables firmly all the wayinto the terminals.If the cables are not inserted allthe way, heat may be generated.*1 Make sure that there are no bare wiresexposed outside the product.Screws (B)Cable covers (A)DC OUT terminalAC cablebinder holeAC IN terminal view> view>DC cablebinder holePower supply unit (with cable coversremoved)Attach to the DIN railAttach in the order described below so that hook (b) is positioned at the bottom.1 Hang hook (a) on the DIN rail (A).2 Pull and hold the lever down (B).3 Secure hook (b) to the DIN rail (C).Hook (a)ABCHook (b)Main monitor installation positionInstalling the main monitorMain monitorinstallation position82.5 mm82.7 mm2 Connect the DC cable and wires.● Connect the wires correctly according to "Wiring schematicdiagram".3 Mount the main monitor to the mounting bracket.3-1 Line up the tab on the bottom of the bracket with the groove on the main monitor (A).3-2 Line up the tab on the top of the bracket with the groove on the main monitor, andpush the main monitor down until it is secure (B).Wall1 Attach the mounting bracket to the wallsecurely.● Install the mounting bracket on a verticalflat wall.A Remove screw A and then remove theterminal cover.B Loosen screw B and push in the wires ofthe DC cable to the terminal connectors(non-polar), then tighten the screws.● Recommended torque:0.8 N·m {8.2 kgf·cm}C Use the cable binder (accessory) tosecure the DC cable (double-coatedarea) to the main monitor.D Make sure to replace the terminal cover.How to connect the DC cable:While pressing on the button with a point-ed object such as a screwdriver, insertthe wire into the terminal connector. (Todisconnect a wire, while pressing on thebutton, pull out the wire.)Bare wire at tip9 mmTerminal ButtonWiring fromdoorphoneImportant:Do not connect the power cable.(Damage may occur.)How to make wiring connections:Reset buttonSD cardslot20 cm20 cm20 cm20 cmCable binder(accessory)12 mmBare wire at tip Screw B● For the following reasons, leave at least 20 cm of spaceabove, below, and to the left and right sides of the mainmonitor:- To prevent malfunction and sound cutting out- To ensure SD cards can be inserted and removed,and to make sure the reset button can be used( the SD card slot is on the side of the main monitor;the reset button is on the bottom)■ About the installation position of the main monitor and mounting bracket● Place the main monitor in a location that your eyes are the same height as the centreof the display.● After deciding where to install the main monitor, attachthe mounting bracket in the location shown on theright.Doorphone installation position Installing the power supply unitImage range:Approx. 900Approx. 500Approx. 85° Approx. 170°Centre (default)Image range:Approx. 900Approx. 85°RightImage range:Approx. 900Approx. 500Approx. 170° Approx. 85°Approx. 500Approx. 850Approx. 1,450Approx. 55032 mmWhen set to wide (default)Centre ofdoorphoneCentre ofdoorphoneCentre ofdoorphoneApprox. 95°Centre ofdoorphoneApprox. 1,450 Approx. 500Approx. 900 Approx. 170°Approx. 500Approx. 1,100Approx. 2,000Image rangeImage displayed onmain monitor:View when lookingfrom aboveView when lookingfrom above(Units: mm)Notes about electrical wiringMake sure not to pinch the wires (as shown to theright) on the mounting bracket when installing.● Do not forcibly attach to the mounting bracket.Vertical, flat wallScrews(locally procured)Hole in wall83.560750Mounting bracket(Units: mm)(Units: mm)(Units: mm)(Units: mm)

/ 2

Related manuals for Panasonic VL-SWD501EX