Panasonic U-8ME1E81 Service Manual

Also see for S-106ME1E5: Installation instructions Instruction manual Service manual Service manual Service manual

Panasonic U-8ME1E81 Service Manual Manual pdf 81 page image

3-312WAY SYSTEMTrouble Diagnosis123456786. Inspection and Characteristics of Parts6. Inspection of Parts 2WAY SYSTEMTrouble Diagnosis(1) High-Pressure Switch (63PH1, 63PH2, 63PH3), Optional High-Pressure Switch for Renewal (63PH4,63PH5)63PH1Measure the resistance between socket pins 1 and 3.The resistance is OK if the result is 0 Ω.(2) Electronic Control Valve (MOV1, MOV2, MOV4)After removing the connector from the PCB, use the following methods to check the valves.When the voltage is normal, measure the resistance between each pair of pins on the electroniccontrol valve connector.The connector is normal if all results (pin 5 – pin 1, pin 5 – pin 2, pin 5 – pin 3, pin 5 – pin 4)are approximately 46Ω. (If the results are 0Ω or , replace the coil.)(3) Crankcase Heater• Connect a clamp meter to 1 of the 2 crankcase heater wires and measure the current.The current is normal if the result is 0.15 A or higher.(As a guide, the current should be 0.1 A (198 V) – 0.2 A (264 V).)MOV1 Measure the voltage between plug pin 5 and pins 1 through 4 at the CN64 connector (5P, white)on the outdoor unit control PCB.(Because of the pulse output, a simplified measurement method is used.Set the tester to the 12 V range; if the value displayed is approximately 4 V, then the voltageis normal.)When the voltage is normal, measure the resistance between each pair of pins on the electroniccontrol valve connector.The connector is normal if all results (pin 5 – pin 1, pin 5 – pin 2, pin 5 – pin 3, pin 5 – pin 4)are approximately 46Ω. (If the results are 0Ω or , replace the coil.)When the voltage is normal, measure the resistance between each pair of pins on the electroniccontrol valve connector.The connector is normal if all results (pin 5 – pin 1, pin 5 – pin 2, pin 5 – pin 3, pin 5 – pin 4)are approximately 46Ω. (If the results are 0Ω or , replace the coil.)MOV2 Measure the voltage between plug pin 5 and pins 1 through 4 at the CN63 connector (5P, red)on the outdoor unit control PCB.(Because of the pulse output, a simplified measurement method is used.Set the tester to the 12 V range; if the value displayed is approximately 4 V, then the voltageis normal.)MOV4 Measure the voltage between plug pin 5 and pins 1 through 4 at the CN57 connector (5P, blue)on the outdoor unit control PCB.(Because of the pulse output, a simplified measurement method is used.Set the tester to the 12 V range; if the value displayed is approximately 4 V, then the voltageis normal.)63PH2Measure the resistance between socket pins 1 and 3.The resistance is OK if the result is 0 Ω.63PH3Measure the resistance between socket pins 1 and 3.The resistance is OK if the result is 0 Ω.63PH4/63PH5Disconnect the CN3 connector (3P, white) from the outdoor unit control panel.Disconnect the CN4 connector (3P, red) from the outdoor unit control panel.Disconnect the CN5 connector (3P, yellow) from the outdoor unit control panel.Disconnect the CN42 connector (4P, white) from the outdoor unit control panel.Measure the resistance between socket pins 1 and 2. The resistance is OK if the result is 0 Ω.Measure the resistance between socket pins 3 and 4. The resistance is OK if the result is 0 Ω.