6. Write the values calculated in 5 above in the gamma data part in EEPROM.EEPROM Adr: 0C58h ~ 0C5Bh, 0C5Ch ~ 0C5Fh ...R (color temperature Normal)0C08h ~ 0C0Bh, 0C0Ch ~ 0C0Fh ...G (color temperature Normal)0C30h ~ 0C33h, 0C34h ~ 0C37h ...B (color temperature Normal)0C50h ~ 0C53h, 0C54h ~ 0C57h ...R (color temperature Warm)0C00h ~ 0C03h, 0C04h ~ 0C07h ...G (color temperature Warm)0C28h ~ 0C2Bh, 0C2Ch ~ 0C2Fh ...B (color temperature Warm)0C60h ~ 0C63h, 0C64h ~ 0C67h ...R (color temperature Cool)0C10h ~ 0C13h, 0C14h ~ 0C17h ...G (color temperature Cool)0C38h ~ 0C3Bh, 0C3Ch ~ 0C3Fh ...B (color temperature Cool)Note:For T.T., P.P. and M.P., record the brightness and chromaticity coordinates for white, red, green, and blue at CHECK andGRAY in the final gamma setting.Also for P.P. and M.P. record the brightness and chromaticity coordinates at colortemperatures Normal and Warm.7. Reflect the data in 6 above and CHECK that the chromaticity coordinates, at check and GRAY, are within the values givenbelow.CHECK: x= 0.2839 y= 0.2884 (TX-32LX1M, TC-32LX1D Series), x=0.2900, y=0.2930 (TX-26LX1M, TC-26LX1D Series)GRAY: x= 0.29 y= 0.29 (TX-32LX1M, TC-32LX1D Series), x=0.2914, y=0.2914 (TX-26LX1M, TC-26LX1D Series) When writing data into EEPROM, make this procedure after sending the WP (write protect) cancellation command (70 8800). Also, WP (write protect) setting command is 70 88 FF.8. EEPROM DATA saving place for WB (gamma data) backup <32 inch>0C18h ~ 0C1Bh 0C08h ~ 0C0Bh0C1Ch ~ 0C1Fh 0C0Ch ~ 0C0Fh0C40h ~ 0C43h 0C30h ~ 0C33h0C44h ~ 0C47h 0C34h ~ 0C37h0C68h ~ 0C6Bh 0C58h ~ 0C5Bh0C6Ch ~ 0C6Fh 0C5Ch ~ 0C5Fh<26 inch>0C20h ~ 0C23h 0C08h ~ 0C0Bh0C24h ~ 0C27h 0C0Ch ~ 0C0Fh0C48h ~ 0C48h 0C30h ~ 0C33h0C4ch ~ 0C4Fh 0C34h ~ 0C37h0C70h ~ 0C73h 0C58h ~ 0C5Bh0C74h ~ 0C77h 0C5Ch ~ 0C5FhNote:After completion of adjustment, record the completion time if it took more than 35 minutes after aging.22TX-32LX1X / TX-32LX1M / TX-32LX1A / TX-32LX1T / TC-32LX1H / TC-32LX1DJ / TX-26LX1X / TX-26LX1M / TX-26LX1A / TX-26LX1T / TC-26LX1H