Panasonic TH-85PF12U Operating Instructions Manual

Also see for TH-85PF12U: Specifications Installation manual Operating instructions Operating instructions Service manual

Contents

Panasonic TH-85PF12U Operating Instructions Manual Manual pdf 56 page image

56Item AdjustmentsINPUT lockOff PC INPUT1 INPUT2 INPUT3Locks the input switch operation.Notes:• Only the adjusted signal is displayed (see page 15).• Signal can be displayed when the Terminal board is installed.• Input switch can be used when this is set to “Off”.• In two screen display mode, if anything other than “Off” is set, the value will be xed as the value input inthe single screen display mode.• When a dual input terminal board is attached, A or B is displayed depending on the selected input signal.(Ex. INPUT1A, INPUT1B)Button lockOff MENU&ENTER OnOff: All the buttons on main unit can be used.MENU&ENTER:Locks MENUMENU and ENTER/ENTER/ buttons on right side of main unit.On: Locks all the button on bottom face of main unit.Sets Button lock with the unit buttons in the following procedure.Off: Press + / four times Press INPUT four times Press - / four times Press ENTER/ENTER/MENU&ENTER: Press ENTER/ENTER/ four times Press + / four times Press INPUT four times Press ENTER/ENTER/On: Press - / four times Press ENTER/ENTER/ four times Press + / four times Press ENTER/ENTER/Remocon User levelOff User1 User2 User3Off: You can use all of the buttons on the remote control.User1: You can only use , , , , , , , buttons on the remote control.User2: You can only use , , buttons on the remote control.User3: Locks all the buttons on remote control.Off-timer functionEnable: Enables the “Off-timer function”.Disable: Disables the “Off-timer function”.Note: When “Disable” is set, the Off-timer is cancelled.Initial Power ModeNormal Standby OnSets the power mode of the unit for when the power recovers from failure or after plugging off and in again.Normal: Power returns in as the same state as before the power interruption.Standby: Power returns in standby mode. (Power Indicator : red/orange)On: Power returns in power On. (Power Indicator : green)Note: When using multiple displays, “Standby” is preferred to be set in order to reduce a power load.ID selectSets panel ID number when panel is used in “Remote ID” or “Serial ID”.Set value range: 0 - 100(Standard value: 0)Remote IDThe setting of this menu is valid only when using ID remote control.Off: Disables ID remote control functions. You can use normal remote control operations.On: Enable ID remote control functions.Note: To use the ID remote control function, it is necessary to set each ID number of remote control anddisplay unit. About the setting method, please refer to “ID Remote Control Function” (see page 46)and “ID select” (above-mentioned).Serial IDSets the panel ID Control.Off: Disables external control by the ID.On: Enables the external control by the ID.Display sizeAdjusts the image display size on screen.Off: Sets the normal image display size on screen.On: Sets the image display size approximately 95 % of the normal image display.Off OnNotes:• This setting is valid only when the input signals are as follows;NTSC, PAL, SECAM, M.NTSC, PAL60, PAL-M, PAL-N (BNC Dual Video Terminal Board (TY-FB9BD))525i, 525p, 625i, 625p, 750/60p, 750/50p, 1125/60i, 1125/50i, 1125/24sF, 1125/25p, 1125/24p, 1125/30p,1125/60p, 1125/50p, 1250/50i (Component Video, RGB, DVI, SDI, HDMI)• This setting is invalid when two screen display, digital zoom, Multi display or Portrait display is selected.• When “Display size” is set to “On”, “H-POS” and “V-POS” in “POS. /SIZE” can be adjusted.• Refer to each board’s operating instruction for DVI, SDI, HDMI’s corresponding signals.Options Adjustments