Panasonic MQ-W Series Instruction Manual

Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use productswhich meet laws and standards, such as OSHA, ANSI or IEC etc., forpersonnel protection applicable in each region or country.SPECIFICATIONS1 40mm type 200mm type 700mm typeModel No.MQ-W3A-DC12-24VMQ-W3AR-DC12-24VMQ-WN3A-DC12-24VMQ-W20A-DC12-24VMQ-W20AR-DC12-24VMQ-WN20A-DC12-24VMQ-W70A-DC12-24VMQ-WN70A-DC12-24VPart numberAN50510AN50510RAN50511AN50530AN50530RAN50531AN50550AN50551Output operation ! " #!$ % Operation indicator & '" ( % )I/O CIRCUIT DIAGRAMS2* 1: Selection of output operation by control inputWiring Output operationConnected to +V !Connected to 0V " #!* 1100mA max. 9.6 to 30V DC㧗㧙Color codeInternal circuit Users’ circuit(Brown) +V(Pink) Control input(Blue) 0V(Black) OutputMain circuit LoadDISTANCE ADJUSTMENT31. Point the detection surface of the photoelectric sensor in the detectingdirection and temporarily fasten the unit.2. With no detectable object in position, slowly turn the distance adjust (8:&) #% % '" (;'<) <' 8:& $ % set point.3. Place a detectable object in the detection position, slowly turn the con (!':&) #% % < ' !':&position, that will be the set point.4. Set the control at a position midway between the points found in 2 and 3above.=< 8 > < ? $ > % #<!@ F) G % J K J $ position of the detection surface and repeat the procedure of 1 to 4, or try to de $variation in detectable object position, etc., that is creating the problem.J) > $ % > > % ( % > # )$ % > > ( $ $ > )$ % <CAUTIONS4 This product has been developed / produced for industrial use only. X % J= Y==Z[< X % \<] K^_ "[ ( ;; ) ing voltage. Use with an ambient light level at the light receiving surface of less than10,000` K^$^^^` < q =^^_ z{(Fpolarity full wave voltage] may cause damage to the internal circuit, asurge absorbing element should be used. : % $ $ rosive gas. The sensor is of immersion proof type, but this does not mean that itcan be used in water or where there is direct impingement of rain fordetecting objects. Because the internal circuit can be damaged due to incorrect connec$ % $ % > # < [ # % ( < F operating voltage of the internal circuit as applied to the load relay. If a load greater than 100mA is connected, the output section will be $ #< " % % % put them in the same raceway. This can cause malfunction due to induction. ' F^^ % ^ 2 , or more, cable. " (=^ ) % >is switched on. The front surface of the lens is polycarbonate. This material is resistant % $ $ # $ > $ $ <$ #$ $ > $ matic hydrocarbons. The emitting elements of MQ-W3AR-DC12-24V and MQ-W20AR-DC12-24V '"< : '"<INSTRUCTION MANUAL MQ-W Series'? !<^^K]=_ # > > ; < & Gtion Manual carefully and thoroughly for the correct and optimum use of this < > # # <@ < ;&G!'" G! :;AN ! "#$ %JKFF X> $ , :$ ]^\^F$ ;@ YF=]KK]F 8:@ YF=]KK=\F: %#$ % . ; G " X! [<$ < J^F3

/ 1

Related manuals for Panasonic MQ-W Series

Panasonic SR-DF101 Operating Instructions Manual

This manual is suitable for:

MQ-W Series MQ-W20A-DC12-24V MQ-W20AR-DC12-24V MQ-W3A-DC12-24V MQ-W3AR-DC12-24V MQ-W70A-DC12-24V MQ-WN20A-DC12-24V MQ-WN3A-DC12-24V MQ-WN70A-DC12-24V

Panasonic MQ-W Series Instruction Manual

Product

Learn More

Legal