Panasonic EX-L200 Series Instruction Manual

Panasonic EX-L200 Series Instruction Manual Manual pdf 1 page image

4 WIRINGƔ Make sure to use the cable with connector,&1$Ƒ&Ƒ(optional), when connecting to the pig-tailed type.Ɣ Tighten the fixing ring of the cable with connectorcompletely by hand when mounting. (The tighteningtorque: 0.2N·m)Ɣ ,IWKH¿[LQJULQJLVWLJKWHQHGE\DWRROVXFKDVSOLUHVit may cause connector damage.Ɣ If the tightening is not enough, the fixing ring mayloosen due to vibration, etc.&RQQHFWLQJPHWKRGƔ Insert the cable with connector into a connectingDUHDRIWKLVSURGXFWDQGWZLVWWKH¿[LQJULQJRIWKHFDEOHZLWKFRQQHFWRUWREH¿[HGCable with connector(Optional)Fixing ringPigtailed type'LVFRQQHFWLQJPHWKRGƔ /RRVHQWKH¿[LQJULQJDQGSXOOWRVHSDUDWHWKHFRQ-QHFWRUE\KROGLQJWKH¿[LQJULQJFixing ring1RWH %HIRUH GLVFRQQHFWLQJ EH VXUH WKDW WKH ¿[LQJ ULQJ LV FRPSOHWHO\ ORRV-ened. If the cable is pulled by excessive force (15N or more) when the¿[LQJULQJLVWLJKWHQHGWKHFDEOHPD\EUHDN5 ,2&,5&8,7',$*5$06Ɣ 131RXWSXWW\SHMain circuit(Brown) +V(Black) Output (Note 1)(Pink) Outputoperation switchinginput (Note 1, 2)(Blue) 0V50mA max.+-Load12 to 24V DC±10%Ɣ 313RXWSXWW\SHMain circuit(Brown) +V(Blue) 0V50mA max.+-(Black) Output (Note 1)(Pink) Outputoperation switchinginput (Note 1, 2)Load12 to 24V DC±10%Notes: 1) The emitter of thru-beam type dose not incorporate output (black)and output operation switching input (pink).2) Be able to select either Light-ON or Dark-ON by wiring the outputoperation switching input (pink) as a following table.Light-ON Dark-ONThru-beam type0LUURUUHÀHFWLYHW\SH Wire to 0V Wire to +V or Open6SRWUHÀHFWLYHW\SH)L[HGIRFXVUHÀHFWLYH7\SHWire to +V or Open Wire to 0V7HUPLQDODUUDQJHPHQW!1 32 4Terminal name1 +V2 Input operation switching input (Note)3 0V4 Output (Note)Note: The emitter of thru-beam type dose not incorporate output and outputoperation switching input.3 02817,1*Ɣ In case mounting this device, use the metal plate06(;/Ƒ (accessory).Without using the metal plate,beam misalignment may occur. Also, install the metalplate in between the sensor and the mounting surface.Ɣ The tightening torque should be 0.5N·m or less withM3 screws.(;/Ƒ(;/Ƒ(;/Ƒ16mmt0.8mm8.2mmMetal plate06(;/(Accessory)(;/Ƒ13mmt0.8mm8.2mmMetal plate06(;/(Accessory)M3 screw(Purchase separately)Ɣ In case using the dedicated sensor mounting bracket(optional) when mounting this device, the metal plate06(;/Ƒ (accessory) is required depending onthe mounting direction. Mount as the diagram belowindicates.(;/ƑMetal plate 06(;/(Accessory)5HTXLULQJWKHPHWDOSODWH!1RWUHTXLULQJWKHPHWDOSODWH!Accessory of the sensormounting bracketSensor mountingbracket (Optional) (Accessory of the sensor mounting bracket)M3 (length: 14mm) screw with washer(;/Ƒ(;/Ƒ(;/Ƒ5HTXLULQJWKHPHWDOSODWH!Metal plate 06(;/(Accessory)1RWUHTXLULQJWKHPHWDOSODWH!Sensor mountingbracket (Optional) (Accessory of the sensor mounting bracket)M3 (length: 14mm) screw with washerAccessory of the sensormounting bracketƔ In case not using the metal plate 06(;/Ƒ (ac-cessory) when mounting this product, work on themounting hole as the diagram below indicates.No chamfering andno burr on mount-ing surface.Chamfering onmounting surface.ChamferingBurr on mountingsurface.Burr1RW*RRG1RW*RRG*RRGTapping for M3 screw 2-ø3.05 ±0.05mmA A:RUNLQJRQWKURXJKKROH7DSSLQJIRU0VFUHZType A(;Ƒ 13±0.05mm(;Ƒ(;Ƒ(;Ƒ16±0.05mmƔ After mounting the thru-beam type, be sure to adjustlight axis of the emission spot to hit the center of thereciever.Emission spotCenter of receiver*RRG 1RW*RRG 1RW*RRG,16758&7,210$18$/$PSOL¿HU%XLOWLQ7\SH/DVHUVHQVRU(;/6HULHVMJE-EXL200 No.0071-60VThank you very much for purchasing Panasonic products.Please read this Instruction Manual carefully and thor-oughly for the correct and optimum use of this product.Kindly keep this manual in a convenient place for quickreference.WARNINGƔ Never use this product as a sensing device for per-sonnel protection.Ɣ In case of using sensing devices for personnelprotection, use products which meet laws and stan-dards, such as OSHA, ANSI or IEC etc., for person-nel protection applicable in each region or country.Ɣ 7KLVSURGXFWLVFODVVL¿HGDVD³&ODVVODVHUSURG-uct” by IEC / JIS standard, GB standard and FDA.Ɣ Do not look the laser directly. Lasers are potentiallyhazardous. Furthermore, do not view the laserZKLFKLVUHÀHFWHGDWDVSHFXODUREMHFWƔ Never disassemble, repair or modify the product.Ɣ In case of control or adjustment using proceduresRWKHUWKDQWKRVHVSHFL¿HGLQWKLVLQVWUXFWLRQPDQX-al, hazardous laser radiation exposure can result. )256$)(86(2)$/$6(5352'8&7Ɣ In order to prevent the accident by laser product andprotect the users, JIS C 6802 -2014 “Safety of laserproducts” was established based on the regulationof IEC (International electrotechnical Commission).This regulation classifies laser products accordingto the level of hazard, and provides the safety mea-sures for respective classes.7KLVSURGXFWDUHFODVVL¿HGDV³&ODVVODVHUSURG-XFWV” according to IEC 60825-1 -2014 (JIS C 6802 -2014 ) “Safety of laser products”.Ɣ This product complies with 21 CFR 1040.10 and1040.11 based on Laser Notice No. 50, dated June24, 2007, issued by CDRH (Center for Devices andRadiological Health) under FDA (Food and Drug Ad-ministration).For details, refer to the Laser Notice No. 50.Ɣ /DVHUKD]DUGRXVFODVV&ODVVL¿FDWLRQDFFRUGLQJWR,(&-2014 (JIS C6802 -2014 )&ODVVL¿FDWLRQ DescriptionClass 1 Safe under reasonably foreseeable conditions.Ɣ /DEHO• )ROORZLQJODEHOVDUHDႈ[HGRQWKLVSURGXFWEDVHGRQthe IEC 60825-1 -2014 standard.:DUQLQJODEHO!Warning label&HUWL¿FDWLRQ ,GHQWL¿FDWLRQODEHO/DEHOSRVLWLRQ!2 3$57'(6&5,37,21Stability indica-tor (Green)(Note 1)Lights up un-der the stablelight conditionor the stabledark conditionOperation indicator(Orange) (Note 2)Lights up when theoutput is ONSensitivityadjuster(Note 3, 4)Notes: 1) Not incorporated on the emitter of thru-beam type.2) It is the power indicator (Green: lights up when the power is ON) forthe emitter of thru-beam type.3) It is not incorporated in emitter of (;/Ƒ.It is not incorporated in (;/Ƒ.

/ 2

Related manuals for Panasonic EX-L200 Series