Leak Detection Sensor EX-F70 SERIES EX-F60 SERIES 858FIBERSENSORSLASERSENSORSPHOTO-ELECTRICSENSORSMICROPHOTO-ELECTRICSENSORSAREASENSORSLIGHTCURTAINSPRESSURE /FLOWSENSORSINDUCTIVEPROXIMITYSENSORSPARTICULARUSESENSORSSENSOROPTIONSSIMPLEWIRE-SAVINGUNITSWIRE-SAVINGSYSTEMSMEASURE-MENTSENSORSSTATICCONTROLDEVICESENDOSCOPELASERMARKERSPLC /TERMINALSHUMANMACHINEINTERFACESENERGYCONSUMPTIONVISUALIZATIONCOMPONENTSFACOMPONENTSMACHINEVISIONSYSTEMSUVCURINGSYSTEMSSelectionGuideWaferDetectionLiquid LeakDetectionLiquid LevelDetectionWaterDetectionColor MarkDetectionHot Melt GlueDetectionUltrasonicSmall / SlimObject DetectionObstacleDetectionOtherProductsSQ4EX-F70/EX-F60PRECAUTIONS FOR PROPER USE Refer to General precautions.EX-F71(-PN) EX-F72(-PN)MountingEX-F71(-PN)• Insert the M4 stud-bolt (length10 mm 0.394 in or more) weldedon the user’s facilities intothe mounting hole of the SUSmounting bracket and screwwith an M4 nut (please arrangeseparately). The tightening torqueshould be 0.98 N·m or less.EX-F72(-PN) case of using the two-point-fixing PVC mounting bracket>• Insert M4 stud-bolts (length10 mm 0.394 in or more)welded on the user’s facilitiesinto the mounting holes ofthe two-point-fixing mountingbracket and screw with M4 nuts(please arrange separately).The tightening torque should be0.49 N·m or less. case of using the PVC mounting bracket for adhesive fixing>• Use adhesive to stick fast the mounting bracket on themounting surface. Please note that if the adhesive sticksout from the bottom surface of the mounting bracket or is0.5 mm 0.020 in, or more thick, the sensor body cannotbe fitted to the mounting bracket.How to fit the sensor body to the exclusive mounting bracket• Match the notch in the sensor bodywith the projection of the exclusivemounting bracket and slide till a clickis felt.• When mounting, make sure to usethe brackets included with the unitin order to eliminate human error (such as forgettingto install). If the included brackets are not used, stablesensing is rendered impossible.Also, because sensitivity settings differ between theEX-F71(-PN) and the EX-F72(-PN), their brackets cannotbe interchanged.EX-F61(-PN) EX-F62(-PN)MountingEX-F61(-PN)• Insert the M4 stud-bolt (length10 mm 0.394 in or more) weldedon the user’s facilities intothe mounting hole of the PFAmounting bracket and screwwith an M4 nut (please arrangeseparately). The tightening torqueshould be 0.98 N·m or less.EX-F62(-PN)• Please note that if the excess adhesive from the bottomsurface of the exclusive mounting bracket is remained,the sensing capability may be affected.Use adhesive for vinyl chloride (PVC).How to fit the sensor body to the exclusive mounting bracket• Align the projections in the sensor body with the notches ofthe exclusive mounting bracket and slide till a click is felt.How to remove the sensor body from the exclusive mounting bracket• Pinch the projections of the sensor body and pull thebody upwards. Never pull the cable, since it may cause acable break.M4 stud-bolt(Straight type)M4 nutSUS plateM4 stud-bolts(Straight type)M4 nutsNotchProjectionM4 nutM4 stud-bolt(Straight type)ProjectionNotchesProjection• Never use this product as a sensing devicefor personnel protection.• In case of using sensing devices forpersonnel protection, use products whichmeet laws and standards, such as OSHA,ANSI or IEC etc., for personnel protectionapplicable in each region or country.
