Panasonic Digital Fiber Sensor FX-301 Specification Sheet

Contents

specifications

520FX-301-FORDER GUIDEFD-F7 series, FT-F9 series12 to 24 V DC10 % Ripple P-P 10 % or lessNormal operation: 960 mW or less (Current consumption 40 mA or less at 24 V supply voltage)ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)NPN open-collector transistor• Maximum sink current: 100 mA (50 mA, if five, or more,amplifiers are connected in cascade.)• Applied voltage: 30 V DC or less (between output and 0 V)• Residual voltage: 1.5 V or less [at 100 mA (50 mA, if five, ormore, amplifiers are connected in cascade.) sink current]Leak setting (F7 mode): OFF with detection of leak, Liquid setting (F9 mode): Using the jog switch, choose the signal OFF condition between absence of liquid and presence of liquid.Incorporated250!s or less (Note 1)Individual teaching / Collective teachingOrange LED (lights up when the output is ON)Green LED [lights up during liquid setting (F9 mode)]RUN: Green LED, TEACH ALL ADJ DISP OUT: Yellow LED4 digit red LED displayIncorporatedDelay timer [used only for liquid setting (F9 mode)] (Timer setting selectable from 10 ms, 100 ms, 1,000 ms, and none)0 to50 C 32 to122 F (If 8 to 16 units are connected in cascade: 0 to45 C 32 to113 F(No dew condensation), Storage: 20 to70 C 4 to158 F35 to 85 % RH, Storage: 35 to 85 % RHSunlight: 10,000 ?x at the light-receiving face, Incandescent light: 3,000 ?x at the light-receiving faceEN 50081-2, EN 50082-2, EN 60947-5-21,000 V AC for one min. between all supply terminals connected together and enclosure (Note 2)20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 2)10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each98 m/s 2 acceleration (10 G approx.) in X, Y and Z directions for five times eachRed LED (modulated)Enclosure: Heat-resistant ABS, Case cover: Polycarbonate, Switch: AcrylicConnector (Note 3)Extension up to total 100 m 328.084 ft is possible with 0.3 mm 2, or more, cable.20 g approx.PNP open-collector transistor• Maximum source current: 100 mA (50 mA, if five, ormore, amplifiers are connected in cascade.)• Applied voltage: 30 V DC or less (between output and V)• Residual voltage: 1.5 V or less [at 100 mA (50 mA, if five, ormore, amplifiers are connected in cascade.) source current]OPTIONSEnd platesAppearance Model No. DescriptionMS-DIN-EWhen cascading multiple amplifiers, or when it moves dependingon the way it is installed on a DIN rail, these end plates ensurethat all amplifiers are mounted together in a secure and fullyconnected manner.Amplifier mountingbracket• MS-DIN-2Fiber sensor amplifierprotection seal• FX-MB1Designation Model No. DescriptionMS-DIN-2 Mounting bracket for amplifierAmplifier mounting bracketFX-MB110 sets of 2 communication window seals and 1 connector sealCommunication window seal:It prevents malfunction due to transmission signal from anotheramplifier, as well as, prevents effect on another amplifier.Connector seal:It prevents contact of any metal, etc., with the pins of the quick-connection cable.Fiber sensor amplifierprotection sealFX-301-FApplicable fibersSupply voltagePower consumptionOutputOutput operationShort-circuit protectionResponse timeSensitivity settingOperation indicatorModel indicatorMODE indicatorDigital displayFine sensitivity adjustment functionTimer functionAmbient temperatureAmbient humidityAmbient illuminanceEMCVoltage withstandabilityInsulation resistanceVibration resistanceShock resistanceEmitting elementMaterialConnecting methodCable extensionWeightItem Model No.NPN outputFX-301P-FPNP outputTypeSPECIFICATIONSEnvironmental resistanceNotes: 1) When detecting leak (output OFF) during leak setting (F7 mode), since the sensor flashes the emitted light, only the response action for turning the signal back to ON is delayed (1 sec. approx.).Notes: 2) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.Notes: 3) The cable for amplifier connection is not supplied as an accessory. Make sure to use the optional quick-connection cable given below.Main cable (3-core): CN-73-C1 (cable length 1 m 3.281 ft), CN-73-C2 (cable length 2 m 6.562 ft), CN-73-C5 (cable length 5 m 16.404 ft)Sub cable (1-core): CN-71-C1 (cable length 1m 3.281 ft), CN-71-C2 (cable length 2 m 6.562 ft), CN-71-C5 (cable length 5 m 16.404 ft)End plates are not supplied with the amplifier. Please order it separately when the amplifiers are mounted in cascade.Two pcs. per set