Panasonic DP-100 Series Instruction Manual

Also see for DP-100 series: Instruction manual Instruction manual Instruction manual

Contents

specifications

Panasonic DP-100 Series Instruction Manual Manual pdf 1 page image

INSTRUCTION MANUALHigh-performance Digital Display Pressure SensorDP-100 SeriesMJE-DP100 No.0025-36VThank you very much for purchasing Panasonic products. Read this Instruction Manualcarefully and thoroughly for the correct and optimum use of this product. Kindly keepthis manual in a convenient place for quick reference.WARNING Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products whichmeet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protec-tion applicable in each region or country. This product is designed for use with non-corrosive gas. It cannot be used for liq-uid or corrosive gas. A product intended for use in Japan conforms to the Japanese Measurement Act.Do not use a product intended for use overseas in Japan.1 PART DESCRIPTIONOutput 1 operationindicatorLights up when com-parative output 1 is ONOutput 2 / analoguevoltage output opera-tion indicatorStandard type:Lights up when com-parative output 2 is ONHigh-function type:Lights up when analoguevoltage output is setMode selection keyUnit display(Note 1, 2)Main displaySub displaySetting valueDOWN keySetting value UP keyConnectionconnectorPressure portDP-100 type: R1 /8 + M5 female screwDP-100-E type: G1 /8 + M5 female screwDP-100-M type: M5 female screwDP-100-N type: NPT1 /8 + M5 female screwNotes: 1) In the case of a model that is intended for use outside Japan, attach the unit switch plate corresponds to the setpressure unit.2) The product for use inside Japan can be set only to “MPa” or “kPa.”2 PIPING When connecting a commercial coupler to the pres-sure port, attach a 12mm spanner (14mm for DP-100-E port, and then tighten with a tightening torque of 9.8N·mor less (M5 female: 1N·m or less). The commercialcoupler or pressure port section will be damaged if thetightening torque is excessive.Wrap sealing tape around the coupler when connect-ing to prevent leaks.12mm spanner3 MOUNTING The sensor mounting bracket MS-DP1-1 is available as an option. When mounting the sen-sor onto the sensor mounting bracket, etc., the tightening torque should be 0.5N·m or less.M3 (length 6mm) screwswith washers(Accessory with MS-DP1-1)Sensor mounting bracketMS-DP1-1 (Optional) The panel mounting bracket MS-DP1-2 (optional) and MS-DP1-4 (optional), as wellas the front cover MS-DP1-3 (optional) and DPX-04 (optional) are also available. The type of the front cover is different depending on the applied mounting bracket.Use MS-DP1-3 for MS-DP1-2, and DPX-04 for MS-DP1-4. For mounting of the panel mounting bracket, refer to the Instruction Manual en-closed with MS-DP1-2 or MS-DP1-4.4 WIRINGConnection method Insert the cable with connector CN-14A-Cinto this product’s connection connector sec- Disconnection method Pressing the release lever of the cable withconnector, pull out the connector.Cable with connectorCN-14A-CRelease leverContact: SPHD-001T-P0.5Housing: PAP-04V-S[JST Mfg. Co., Ltd.]Note: Do not pull by holding the cable without pressing the release lever, as this can cause cable break or connectorbreak.1 2 3 4Connector pin No. Terminal name1 +V2 Comparative output 13 Standard type: Comparative output 2High-function type: Analogue voltage output or external input4 0V5 I/O CIRCUIT DIAGRAMSWhen using the analogue voltage output, take care to the input impedance of theconnected device.Furthermore, note that if the cable is extended, the cable resistance will cause thevoltage to drop.NPN output typeStandard typeMain circuit(Brown) +V(Black)Comparative output 1(White) Comparative output 2(Blue) 0VLoadLoad100mA max.100mA max.+ 12 to 24V DC±10%-High-function typeMain circuit(Brown) +V(White)Analogue voltage outputor external input(Black)Comparative output 1(Blue) 0VLoad100mA max.5V+ 12 to 24V DC±10%-PNP output typeStandard typeMain circuit(Brown) +V(Black) Comparative output 1(White)Comparative output 2(Blue) 0VLoadLoad100mA max.100mA max.+ 12 to 24V DC±10%-High-function typeMain circuit(Brown) +V(White)Analogue voltage outputor external input(Black)Comparative output 1(Blue) 0VLoad100mA max. + 12 to 24V DC±10%-6 OUTPUT MODE AND OUTPUT OPERATION The EASY mode, hysteresis mode or window comparator mode can be selected asthe output mode for comparative output 1 and comparative output 2.Refer to in “ 8 MENU SET-TING MODE” for details.EASY mode ON / OFF of the comparative output is controlled in this mode.PressureP0ONOFFComparativeoutputH (Hysteresis) ! ! "# Refer to in “ 9 PRO MODE” for setting.2) “ ” is displayed for comparative output 1 and “ ” for comparative output 2 on the sub-display.Hysteresis mode The comparative output ON / OFF state can be controlled with randomly set hyster-esis in this mode.0PressureComparativeoutputH (Hysteresis)HiLoONOFFH: 1digit or more2 digits or more whenusing psi unitNote: “ ” or “ ” is displayed for comparative output 1 and “ ” or “ ” for comparative output 2 on thesub-display.

/ 4

Related manuals for Panasonic DP-100 series