Panasonic DMP-BD65 Operating Instructions Manual

Also see for DMP-BD45: Operating instructions Basic operating instructions Basic operating instructions

Panasonic DMP-BD65 Operating Instructions Manual Manual pdf 27 page image

27VQT2H94SettingsStill ModeSelect the type of picture shown when you pause playback.Seamless PlayThe chapters segment in playlists are played seamlessly.≥ Select “On”, when the picture freezes for a moment at thechapters segment in playlists.NTSC Contents OutputSelect PAL60 or NTSC output when playing NTSC discs.Dynamic Range CompressionYou can listen at low volumes but still hear dialog clearly.(Dolby Digital, Dolby Digital Plus and Dolby TrueHD only)≥ “Auto” is effective only when playing Dolby TrueHD.Digital Audio Output (> 33)Press [OK] to show the following settings.PCM Down ConversionSelect how to output audio with a sampling frequency of96 kHz for the PCM output from the DIGITAL AUDIO OUT.≥ If “On” is selected, the signals that are converted to 48 kHzare output.≥ If “Off” is selected, and the connected equipment does notsupport 96 kHz, the sound will not be output normally.≥ Signals are converted to 48 kHz despite the settings acrossin the following cases:– when the signals have a sampling frequency of 192 kHz– when the disc has copy protection– when “BD-Video Secondary Audio” is set to “On”DownmixSelect the downmix system of multi-channel to 2-channelssound.≥ Select “Surround encoded”, when the connected equipmentsupports the virtual surround function.≥ There is no effect on “Bitstream” via HDMI AV OUT andDIGITAL AUDIO OUT.≥ The audio will be output in “Stereo” in the following cases.– AVCHD playback– Playback of secondary audio (including the button clicksound).7.1ch Audio Reformatting [BD65]Surround sound with 6.1ch or less is automatically expandedand played back at 7.1ch.≥ If “Off” is selected, sound is played over the original numberof channels.(Note that in the case of 6.1ch audio, playback will be at5.1ch.)Audio reformatting is enabled in the following cases:≥ When you have selected “PCM” in “Digital Audio Output”.≥ When the audio is Dolby Digital, Dolby Digital Plus, DolbyTrueHD or LPCM.On-Screen MessagesChoose whether to show status messages automatically.On-Screen LanguageChoose the language for these menus and on-screenmessages.Screen Saver FunctionThis is to prevent burn-in on the screen.≥ When this is set to “On”:If there is no operation for 10 minutes or more, DIRECTNAVIGATOR screen switches to FUNCTION screenautomatically.≥ While playing and pausing, etc., this function is notavailable.≥ As for Music [CD-DA] or MP3, regardless of the setting, ifthere is no operation for a while, DIRECT NAVIGATORscreen switches to the other states automatically.FL DisplayChanges the brightness of the unit’s display.≥ If “Automatic” is selected the display is dimmed duringplayback and bright except during playback.Software LicenceInformation about the software used by this unit is displayed.PictureAutomatic Automatically selects the type of pictureshown.Field Select if jittering occurs when “Automatic” isselected.Frame Select if small text or fine patterns cannot beseen clearly when “Automatic” is selected.SoundDolby D/Dolby D +/Dolby TrueHDDTS/DTS-HDMPEG AudioSelect the audio signal to output.≥ Select “PCM”, when the connected equipment cannotdecode the respective audio format.≥ Not making the proper settings may result in noise.BD-Video Secondary AudioSelect whether to mix or not mix the primary audio andsecondary audio (including the button click sound). (> 18)≥ If “Off” is selected, the unit outputs the primary audio only.Display