Panasonic CF-74 Series Operating Instructions Manual

Also see for CF-74 Series: Operating instructions Supplementary guide Supplementary guide Supplementary instructions Operating instructions

Contents

Panasonic CF-74 Series Operating Instructions Manual Manual pdf 23 page image

23 Getting StartedUseful InformationTroubleshootingAppendixTroubleshooting (Basic)Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contactPanasonic Technical Support (Î page 30). You can also check the computer’s status in the PC Information Viewer(Î Reference Manual “Troubleshooting (Advanced)”). Starting UpCannot start up.The power indicator or bat-tery indicator is not lit.z Connect the AC adaptor.z Insert a fully charged battery.z Remove the battery pack and the AC adaptor, then connect them again.z If a device is connected to the ExpressCard slot or the USB port, disconnect thedevice, or set [ExpressCard Slot], [USB Port] or [Legacy USB Support] to [Disable]in the [Advanced] menu of the Setup Utility.The power is turned on but“Warming up the system (upto 30 minutes)” appears.z The computer is warming up before start up. Wait for the computer to start up (takes upto 30 minutes). If, “Cannot warm up the system” is displayed, the computer failed towarm up and does not start. In this case, turn off the computer, leave it in an environ-ment of 5 °C {41 °F} or higher temperature for about an hour, and then turn on the poweragain.Cannot turn on the computer.The computer does notresume from standby.(The power indicator blinksquickly in green.)z Leave it in an environment of 5 °C {41 °F} or higher temperature for about an hour, thenturn on the power again.You have forgotten thepassword.z Supervisor Password or User Password: Contact Panasonic Technical Support (Î page30).z Administrator password:• If you have a password reset disk, you can reset the administrator password. Set thedisk and enter any wrong password, then follow the on-screen instructions and set anew password.• If you do not have a password reset disk, reinstall (Î page 20) and set up Windows,and then set a new password.“Remove disks or othermedia. Press any key torestart” or a similar mes-sage appears.z A floppy disk is in the drive and it does not contain system startup information. Removethe floppy disk and press any key.z This message may appear with some devices connected to the ExpressCard slot or theUSB port . Remove the device, or set [ExpressCard Slot], [USB Port] or [Legacy USBSupport] to [Disable] in the [Advanced] menu of the Setup Utility.z If the problem persists after removing the disk, it may be a hard disk failure. ContactPanasonic Technical Support (Î page 30).Windows startup and opera-tion is slow.z Press F9 in the Setup Utility (Î page 22 “To start the Setup Utility”) to return the SetupUtility settings (excluding the passwords) to the default values. Start the Setup Utility andmake the settings again. (Note that the processing speed depends on the applicationsoftware, so this procedure may not make Windows faster.)z If you installed a resident software after purchase, turn off the residence.z Disable Indexing Service in the following menu.Click [start] - [Search] - [Change preferences] - [Without Indexing Service]The date and time are incor-rect.z Make the correct settings. Click [start] - [Control Panel] - [Date, Time, Language, andRegional Options] - [Date and Time].z If the problem persists, the internal clock battery may need to be replaced. ContactPanasonic Technical Support (Î page 30).z When the computer is connected to LAN, check the date and time of the server.z The 2100 A.D. or later year will not be correctly recognized on this computer.[Executing Battery Recali-bration] screen appears.z The Battery Recalibration was canceled before Windows was shut down last time. Tostart up Windows, turn off the computer by the power button, and then turn on.[Enter Password] does notappear when resuming fromstandby/hibernation.z To display [Enter Password] at resuming, set the Windows password. The password youhave set in the Setup Utility is not requested at resuming.A Click [start] - [Control Panel] - [User Accounts] and select the account, and set thepassword.B Click [start] - [Control Panel] - [Performance and Maintenance] - [Power Options] -[Advanced] and add a check mark for [Prompt for password when computer resumesfrom standby].