3 Getting StartedRead Me FirstModels for U.S.A.Federal Communications Commission Radio Fre-quency Interference StatementNote: This equipment has been tested and found to comply withthe limits for a Class B digital device, pursuant to Part 15 of theFCC Rules. These limits are designed to provide reasonableprotection against harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by oneor more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment andreceiver. Connect the equipment into an outlet on a circuit dif-ferent from that to which the receiver is connected. Consult the Panasonic Service Center or an experi-enced radio/TV technician for help.WarningTo assure continued compliance, use only shielded inter-face cables when connecting to a computer or peripheral.Also, any changes or modifications not expressly ap-proved by the party responsible for compliance could voidthe user’s authority to operate this equipment.FCC RF Exposure Warning: This equipment is provided with PC Card slot that couldbe used with wireless transmitters, which will be specifi-cally recommended when they become available.Other third-party wireless transmitters have not beenRF exposure evaluated for use with this computer andmay not comply with FCC RF exposure requirements. This equipment complies with FCC radiation exposurelimits set forth for an uncontrolled environment. This equipment may not be co-located or operatedwith any other antenna or transmitter. This equipment has been approved for portable operation,and unless otherwise advised in separate supplementalinstructions for individual wireless transmitter(s), requiresminimum 1.5 cm spacing be provided between antenna(s)and all person’s body (excluding extremities of hands,wrist and feet) during wireless modes of operation. This equipment may use multiple installed transmitters,which may be capable of simultaneous transmission. This equipment is provided with external antennaconnector(s) for connection to optional Car Mounter orPort Replicator for mobile external mounted antenna(s).External antenna(s) must be professionally installed andcannot exceed recommended maximum antenna gain asdescribed in individual provided supplement instructionsfor wireless transmitters. Also, user must maintain mini-mum 20 cm spacing between external antenna(s) and allperson’s body (excluding extremities of hands, wrist andfeet) during wireless modes of operation. WLAN external antenna connector is intended for con-nection to Radiall/Larsen WLAN Base Whip antenna,type NM05E2400BKTNC with 5 dBi antenna. WWAN external antenna connector is intended forprofessional installation and should not exceed maxi-mum antenna gain of 9.85 dBi for 824.7 - 848.31 MHzoperation and 8.34 dBi for 1851.25 - 1908.75 MHzoperation.This device complies with Part 15 of the FCC Rules Op-eration is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received,including interference that may cause undesired op-eration.Responsible Party: Panasonic Corporation of North AmericaOne Panasonic WaySecaucus, NJ 07094Tel No:1-800-LAPTOP5 (1-800-527-8675)6-M-1FCC Regulation Notice for modemThis equipment contains a FCC approved modem.1. This equipment complies with CFR47 Part 68 rules.On the computer is a label that contains, among otherinformation, the FCC registration number and ringerequivalence number (REN) for this equipment. If re-quired, this information must be provided to the tele-phone company.2. An FCC compliant telephone cord and modular plugis provided with this equipment. This equipment isdesigned to be connected to the telephone networkor premises wiring using a compatible modular jackwhich is Part 68 compliant. See Installation Instruc-tions for details.3. The REN is used to determine the quantity of deviceswhich may be connected to the telephone line. Ex-cessive RENs on the telephone line may result in thedevices not ringing in response to an incoming call. Inmost, but not all area, the sum of RENs should not ex-ceed five (5.0). To be certain of the number of devicesthat may be connected to a line, as determined by thetotal RENs, contact the local telephone company.4. If your telephone equipment cause harm to the tele-phone network, the telephone company will notify youin advice that temporary discontinuance of servicemay be required. But if advice notice isn’t practical, thetelephone company will notify the customer as soonas possible. Also, you will be advised of your right tofile a complaint with the FCC if you believe it is neces-sary.5. The telephone company may take changes in its facili-ties, equipment, operations or procedures that couldaffect the operation of the equipment. If this happensthe telephone company will provide advance noticein order for you to make necessary modifications tomaintain uninterrupted service.6. If trouble is experienced with this equipment, for repairor warranty information, please contact PanasonicCorporation of North America at DIAL TOLL FREE1-800-LAPTOP5 (1-800-527-8675). If the equipment iscausing harm to the telephone network, the telephonecompany may request that you disconnect the equip-ment until the problem is resolved.7. There are no user serviceable parts contained in thisequipment.8. This equipment may not be used on coin service pro-vided by the telephone company. Connection to partylines is subject to state tariffs.
