Menu
Panasonic BEP-NRH005 Series Instruction Manual
  |
Note:Note:Rotate the front wheel and check that the lamp illuminations.All our components have been designed for bicycles to be used on official public roads only.Note:Connect so that the current from the hub dynamo flows through the cable from the lamp connection terminal of the hub dynamoto the frame connection terminal.To disconnect the lamp from the hub dynamo, remove the connector cover.Bend the cable wires and runthem along the grooves.Do not allow the cable wiresto touch each other.Note:Connect the cables as shown in the illustration below.Connection of the cablesNote: Scrape away the paint from the lamp’ s frame connection terminal and the lamp connection terminal whenconnecting the cables.TypeWireInsulationStandedSize(AWG)22Diameter approx.0.8mmDiameter 1.8 - 2mmDo not switch over the frame cable and the light cable bymistake. If the cables are connected incorrectly, the lightwill not illuminate.Twist the cable wires before connecting them so that theystay together.Recommended wire specifications.Checking the lamp illuminationSpecificationsNote:Compatible bulbsFrontlamp Taillamp6V-2.4W 6V-0.6W6V-3.0WInsertBendGrooveInsulationWireRemoveConnectorcoverConnectConnectorcoverCableFront fork Do not ride the bicycle while the connector coveris removed, otherwise the cable might get caughtin the bicycle wheel.When removing the bicycle wheel, first removethe connector cover. If the cables are pulledstrongly, it may break the cable wires or causepoor contacts. Furthermore, when installingthe wheel, first secure the wheel to the front forksand then connect the connector cover.Instruction ManualHub DynamoModel No. BEP-NRH005 SeriesPutting Together the Front Wheel Mounting AssemblyNote:1. Align the front wheel (hub dynamo) in its mounting position. As shown in the diagram. The connection terminal of thehub dynamo should be on the side (when the bicycle is facing forward). The connection terminal should be positionedbetween the front fork and the basket stay.2. Assemble the fender stays and basket stays. Make sure that the hub washer and hub nut or volute spring and quick release nuthave been put on in the correct order.3. Tighten the hub nut .(1) Tighten the left and right hub nuts alternately, little by little, to course that the hub dynamo connection terminal do notturn away from the correct orientation.(2) The recommended hub nut tightening torque is 20-25N- m.Tightening torque :20-25N -mWhen tightening the cap nuts, tighten the nuts alternately on both sides and do not concentrate all of the effort for tighteningand loosening the cap nut on one side of the wheel only, otherwise the hub axle may turn, which could excessively tighten orloosen the lock nuts.Frame ConnectionterminalLampconnectionterminalLamp cableFrame cableApprox.12 mmApprox.12 mmConnector capFrameconnectionterminalLamp connection terminalEarth markHub dynamo connectionterminalManufacturer:Suzhou Sanyo Electro-mechanical co.,Ltd,No.1025 Sunwu Road, Xukou, Wuzhong District, Suzhou 215164, ChinaRepresentative in Europe:Panasonic Europe Ltd.Panasonic Testing CentreWinsbergring 15, 22525 Hamburg, GermanyModel No.WheelTire outer diameterCompatiblesizeBEP-NRH005 SeriesVoltage/Output400-660 mm16-26 inch6 V/3.0WNote:According to the German regulation you need to use an OVP. This dynamo has not implemented an OVP function in to the inner housing.Therefore, please do use an external OVP, the NKV006 approved by Panasonic, in case that your front light will not include OVP function inside.Please do use the approved Panasonic OVP NKV006. Use an external overvoltage protector.Do not disassemble the internal hub mechanism.Do not apply any lubricant to the inside of the hub, otherwise the grease will come out and it may cause problems with conductivity.If the hub nuts are screwed on too tight, or if one or the other is screwed tighter or looser than the other, the hub axle may be forced to turn.Contact your dealer for repairs if the tire needs replacement or the hub nuts are loose.Check the degree of parallel of the front fork end. If the front fork end is severely out of parallel, deformation of the hub axle may cause noisefrom an obstruction inside the hub dynamo to be generated.Be sure to install the hub dynamo to the front fork so that the side with the connection terminal is on the right when facing toward the front ofthe bicycle. If the side with the connection terminal is facing toward the left, the hub dynamo may not turn properly while riding.Lamps with electrical circuits such as automatic lamps may become damaged if the bicycle is ridden at high speeds.If the lamp is frequently turned on when riding at high speed ranges, it will shorten the operating life of the bulbs.Parts are not guaranteed against natural wear or deterioration resulting from normal use.Check that the wheels are fastened securely before riding the bicycle. If the wheels are loose in any way, theymay come off the bicycle and serious injury may result.Check that the lamp illuminates normally when riding at night time.IMPORTANT SAFETY INSTRUCTIONSIMPORTANTCAUTION!CAUTION!! WARNING! WARNINGDenotes a potential hazard that could result in serious injury .Denotes a hazard that could result in minor injury or damage to the unit or other equipment.This manual contains safety information. Read manual completely before first using this product, and save this manual for future use.The hub dynamo generates an extremely high voltage. Touching the dynamo terminal may cause an electric shock.Never touch the connection terminal of the hub dynamo directly while riding the bicycle or while the wheel is spinning.Explanation of symbolsHub dynamoHub dynamoconnectionterminalFender stayBasket stayFront forkHub dynamoHub dynamoconnectionterminal Front forkHub nut (BC 3/8)Hub washerFender stayBasket stay |
This manual is suitable for:
Product
Learn More
Legal
Copyright © 2024 OneStart. All Rights Reserved