Panasonic AW-RP501 Service Manual

Also see for AWRP501 - HYBRID CONTROL PANEL: Operating instructions Operating instructions

Contents

Panasonic AW-RP501 Service Manual Manual pdf 2 page image

This service information is designed for experienced repair technicians only and is not designed for use by thegeneral public.It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting toservice a product.Products powered by electricity should be serviced or repaired only by experienced professional technicians. Anyattempt to service or repair the product or products dealt with in this service information by anyone else couldresult in serious injury or death.! WARNINGCAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK,DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICEPERSONNEL.This symbol warns the user that uninsulated voltage withinthe unit may have sufficient magnitude to cause electricshock. Therefore, it is dangerous to make any kind of contactwith any inside part of this unit.This symbol alerts the user that impotant literature concerningthe operation and maintenance of this has been included.Therefore, it should be read carefully in order to avoidany problems.T here are special components used in this equipment which are important for safety. These parts are indicatedby the ” Y ” mark on the schematic diagram and the replacement parts list. It is essential that these criticalparts should be replaced with manufacturer's specified parts to prevent shock, fire, or other hazards.Do not modify the original design without permission of manufacture.IMPORTANT SAFETY NOTICE[AW-RP505]Source Voltage : 12 V DC (DC jack)Power Consumption : 12 V, 0.5 APreview Video Input : 1.0 V[p-p] composite/75Ω (BNC connector)Genlock Input : black burst75Ω loop through with auto terminator (BNC connector)Preview Video Output : 1.0 V[p-p] composite/75Ω (BNC connector)Genlock Output : 75Ω (BNC connector)Camera Control Output : Control signal (BNC connector)Pan/tilt Control Output : Control signal (RJ-45 8P modular jack)System Tally Input : Tally signal (6 pin Terminal block)Auxiliary Control Input : Control signal (8 pin DIN connector)Switches : Power ON/OFF Switch, CAM CONT Switch, GAIN HIGH/MID/LOW Switch,GAIN AGC/MANU Switch, SCENE FILE Switch, CONTROL Switch, LAMP Switch,MODE BAR/CAM Switch SHUTTER Switch, AUTO/ATW ATW Switch, AUTO/ATW A Switch,AUTO/ATW B Switch, AWC Switch, ABC Switch, G/L PHASE ON/OFF Switch,G/L PHASE Coarse Switch, IRIS AUTO/MANU Switch, MEMORY Switch, PRESET Switch,DEF Switch, WIP Switch, H/F Switch, EXT Switch, ND Switch, OP Switch, SPEED Switch,Controls : T. PED Control, G/L PHASE SC Control, G/L PHASE H Control, IRIS LEVEL Control,ZOOM Lever, FOCUS Lever, PAN/TILT LeverMultiport Hub ConnectingCable : x 4 (Coaxial Cable 3 pcs., 10BASE-T straight cable 1 pc.)(In case of using G/L function)Maximum cable length : 10 m (In case of using coaxial cables 5C-2V and 10BASE-T straight cable UTP category-5)Operating temperature : −10°C to +45°C (14°F to +113°F)Dimensions : 210 (W) x 88 (H) x 177 (D) mm [8-1/4" (W) x 3-1/2" (H) x 7" (D)]Weight : 2.2 kg (4.9 lbs.)Finish : AV Ivory paintingWeight and dimensions indicated are approximate.Specifications are subject to change without notice.ACCESSORIESSeal ........................................................ 1 Mounting screws ......................................... 12Rack angle .............................................. 2 M4 x 8mm .............................................. 8Connect plate.......................................... 1 M5 x 8mm .............................................. 4