Panasonic AK-HRP200G Operating Instructions Manual

Also see for AK-HRP200G: Operating instructions Operating instructions Operating instructions Operating instructions Operating instructions

Contents

Panasonic AK-HRP200G Operating Instructions Manual Manual pdf 3 page image

3Read this first! (continued)EMC NOTICE FOR THE PURCHASER/USER OF THE APPARATUS1. Applicable standards and operating environment (AK-HRP200)The apparatus is compliant with:• standards EN55103-1 and EN55103-2 2009, and• electromagnetic environments E1 - E5.2. Pre-requisite conditions to achieving compliance with the above standards<1> Peripheral equipment to be connected to the apparatus and special connecting cables• The purchaser/user is urged to use only equipment which has been recommended by us as peripheral equipment to be connected to theapparatus.• The purchaser/user is urged to use only the connecting cables described below.<2> For the connecting cables, use shielded cables which suit the intended purpose of the apparatus.• Video signal connecting cablesUse double shielded coaxial cables, which are designed for 75-ohm type high-frequency applications, for SDI (Serial Digital Interface).Coaxial cables, which are designed for 75-ohm type high-frequency applications, are recommended for analog video signals.• Audio signal connecting cablesIf your apparatus supports AES/EBU serial digital audio signals, use cables designed for AES/EBU.Use shielded cables, which provide quality performance for high-frequency transmission applications, for analog audio signals.• Other connecting cables (LAN, RS-422)Use shielded cables, which provide quality performance for high-frequency applications, as connecting cables.• When connecting to the DVI signal terminal, use a cable with a ferrite core.• If your apparatus is supplied with ferrite core(s), they must be attached on cable(s) following instructions in this manual.3. Performance levelThe performance level of the apparatus is equivalent to or better than the performance level required by these standards.However, the apparatus may be adversely affected by interference if it is being used in an EMC environment, such as an area where strongelectromagnetic fields are generated (by the presence of signal transmission towers, cellular phones, etc.). In order to minimize the adverseeffects of the interference on the apparatus in cases like this, it is recommended that the following steps be taken with the apparatus beingaffected and with its operating environment:1. Place the apparatus at a distance from the source of the interference.2. Change the direction of the apparatus.3. Change the connection method used for the apparatus.4. Connect the apparatus to another power outlet where the power is not shared by any other appliances.IMPORTANT SAFETY INSTRUCTIONS1) Read these instructions.2) Keep these instructions.3) Heed all warnings.4) Follow all instructions.5) Do not use this apparatus near water.6) Clean only with dry cloth.7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. Agrounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plugdoes not fit into your outlet, consult an electrician for replacement of the obsolete outlet.10) Protect the power cable from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from theapparatus.11) Only use attachments/accessories specified by the manufacturer.12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used,use caution when moving the cart/apparatus combination to avoid injury from tip-over.13) Unplug this apparatus during lightning storms or when unused for long periods of time.14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such aspower-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has beenexposed to rain or moisture, does not operate normally, or has been dropped.Декларація про ВідповідністьВимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та електронному обладнанні(затвердженого Постановою №1057 Кабінету Міністрів України)Виріб відповідає вимогам Технічного Регламенту Обмеження Використання деяких Небезпечних Речовин в електричному та електронномуобладнанні (ТР ОВНР).Вміст небезпечних речовин у випадках, не обумовлених в Додатку №2 ТР ОВНР, :1. свинець(Pb) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;2. кадмій (Cd)– не перевищує 0,01 % ваги речовини або в концентрації до 100 частин на мільйон;3. ртуть(Hg) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;4. шестивалентний хром (Cr6+ ) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон;5. полібромбіфеноли (PBB) – не перевищує 0,1% ваги речовини або в концентрації до 1000 частин на мільйон;6. полібромдефенілові ефіри (PBDE) – не перевищує 0,1 % ваги речовини або в концентрації до 1000 частин на мільйон.