Panasonic AG-HMX100 Operating Instructions Manual

Also see for AG-HMX100E: Operating instructions Operating instructions Operating instructions

Panasonic AG-HMX100 Operating Instructions Manual Manual pdf 4 page image

4Chapter 1 Applying Effects to Video and Sound[PATTERN EDGE]An edge can be added to a pattern.Rotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5HARDSOFTBORDERSOFT BORDER1-255 WHITEYELLOWCYANGREENMAGENTAREDBLUEBLACKCUSTOM1CUSTOM2PATTERN HARDEDGE COLORWIDTH32 WHITESelect the edge of transition patterns from [HARD], [SOFT],[BORDER], and [SOFT BORDER] using the rotary 2 control.The factory default setting is [HARD].Set [WIDTH] in the range of 1 to 255 using the rotary 3control.The factory default setting is 32.For No. 701 to No. 707 (24 to 27) and No. 801 to No. 814(183 to 196) patterns, [WIDTH] can be set only to 1 or 2.Use the rotary 4 control to set [COLOR] (color of the edge)to one of the colors in the table shown below.Setting Color[WHITE] (factory default setting) White[YELLOW] Yellow[CYAN] Cyan[GREEN] Green[MAGENTA] Magenta[RED] Red[BLUE] Blue[BLACK] Black[CUSTOM1] or [CUSTOM2] Grey as the factorydefault settingWhen [CUSTOM1] or [CUSTOM2] is selected, the samecolor as set in the [BACK MATTE] submenu of the [INTVIDEO] menu is applied ( page Vol.1-29). NOTEIf the PinP pattern is selected and Still is applied to source•video B, Still is cancelled at the same time as the transitionlever is operated. (The PinP pattern and Still cannot be usedas the same time.)[SOFT BORDER] cannot be selected for No. 701 to No. 707•(24 to 27) and No. 801 to No. 814 (183 to 196) patterns.[EFFECTS]Select the effect of [SHADOW] or [TRAIL] using the rotary2 control.SHADOW: Adds black shadow to the pattern.TRAIL: Leaves trails of the moving pattern.Select [OFF] to apply no effect.Rotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5OFFSHADOWTRAILEFFECTS OFFIf [SHADOW] is selectedRotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5EFFECTS SHADOWSet the position of the shadow by operating the joystickwhile holding down the SHIFT key.The CENTER, SCENE GRABBER, and HOLD buttons flashtemporarily.To cancel the shadow position setting, press the keywhile holding down the SHIFT key in the state where[FEECTS] is selected (inverted to black). At the sametime as the setting becomes [OFF], the specified shadowposition is reset.If [TRAIL] is selectedRotary 1 Rotary 2 Rotary 3 Rotary 4 Rotary 5SELFSELF-SPARKBODMBODM-SPARK1-32EFFECTS TARIL TIMESELF 16Select the spark for the trail (the twinkling effect of trails)from [SELF] (original video), [SELF-SPARK] (spark oforiginal video), [BODM] (border color), and [BODM-SPARK] (border spark) using the rotary 3 control.When [BODM] or [BODM SPARK] is selected, the color setin the [PATTERN EDGE] submenu of the [TRANSITION]menu is used as the border color.Set the continuation time of the trail in the range of 1 to 32using the rotary 4 control.To set the offset position of the trail, operate the joystickwhile holding down the SHIFT key.The CENTER, SCENE GRABBER, and HOLD buttons flashtemporarily.The offset position setting can be cancelled in the sameway as for canceling the shadow position setting. NOTEThe trail or shadow settings are canceled when TRAIL orSHADOW is selected in the [DSK EFFECTS] submenu of the[DSK FADE] menu or when the multi-strobe effect or DECAY isselected in the [VIDEO EFFECTS] menu.