Oasis POU1RRK Instructions Manual

Oasis POU1RRK Instructions Manual Manual pdf 1 page image

OASIS ® WATER COOLER MODELSPOU1RRK, POU1RRHS, POU1SRK, POU1SRHS INSTRUCTIONSA. INSPECTIONInspect the carton and water cooler for evidence of rough handling and concealed damage. Damage claims should be filed with the carrier.B. MAINTENANCE1. Inspect the condenser for dirt and lint every three months. If cleaning is required, disconnect the power supply cord, then clean the condenser with a smallstiff non-wire brush. Observance of this procedure will ensure adequate air circulation through the condenser for efficient and economical operation.2. A cone shaped strainer can be found in the tube leading into the mechanical float valve on the reservoir cap. It can be removed and flushed clean. Be sure toreplace it in the tube once cleaned.C. OVERLOAD PROTECTIONThe compressor motor is equipped with an automatic reset protector which will disconnect the motor from the line in case of an overload.D. LUBRICATIONThis unit is equipped with a hermetically sealed compressor which does not require any additional lubrication.E. TO PUT WATER COOLER INTO SERVICE1. The water cooler should be located a minimum of 2" (51mm) from the wall to assure adequate condenser air circulation.2. If filter(s) are to be added, follow filter manufacturer’s recommended instructions.3. Remove blue plug from “inlet” fitting on the back of the cooler. Push a ¼” OD copper tube into the fitting. Connect to cold water supply.4. WARNING: A pressure regulator, such as a Slow Flow regulator, must be installed in front of the unit’s water inlet if the water pressure (includingany possible pressure spikes) could exceed 100psig (690kpg).5. Turn on water supply to cooler.6. Check the available power supply against the water cooler data plate to assure correct electrical service. Plug power supply cord into receptacle7. CAUTION: On models with a hot tank, the hot tank switch must be in the “OFF” position. Switch is mounted at the rear of the cooler on thecondenser.8. After the reservoir is full, check all connections for leaks.9. Open each faucet until water flows freely.10. On models with a hot tank, turn on the hot tank by depressing the switch toward the “RESET” position.11. CAUTION: Failure to fill hot tank with water before turning on the hot tank can cause physical damage to the unit.12. CAUTION: WATER FROM HOT FAUCET CAN SCALD.F. SAFETY FLOATThe cooler is equipped with a safety float to prevent overfilling in case the fill float fails. If the fill float should fail, the safety float will be activated as thewater level rises. When the safety float is activated, water flow to the reservoir will be shut off. Press the blue reset button about half way down on thereservoir cap until you hear the water flow restart, then call your service representative. CAUTION: A hard impact or jarring of the unit while it isfilling may trip the safety float.G. TO DISCONTINUE USE OF WATER COOLER1. On models with a hot tank, place hot tank switch in the “OFF” position. Draw water from hot faucet until water is cool.2. Disconnect power supply cord.3. Shut off water supply to cooler.4. Drain reservoir through cold faucet.5. On models with a hot tank, drain tank by placing a container under black drain valve located on the condenser. Turn drain valve counter clockwise to open,and catch water in container. OR, for convenience, insert one end of a 3/8” OD tube into the opening of the drain valve and the other into a container anddrain. Close drain valve when the tank is empty.6. ALWAYS DRAIN ALL WATER WHEN FREEZING TEMPERATURES ARE ANTICIPATED OR BEFORE SHIPPING THE WATER COOLER.H. REMOVABLE RESERVOIR1. To Remove Reservoira) Drain the cooler as described in Section G.b) Remove top by lifting it up from the rear.c) Remove float cap assembly by lifting it up and out of the reservoir.d) There may be an ice bank formed around the cooling probe. Pour warm water over the ice to melt it away from the probe.e) Remove the faucets from the reservoir by unscrewing them in a counterclockwise fashion.f) Grasp the top of the reservoir around the opening and pull upward in a straight motion.2. Installing New Reservoira) Align reservoir with probe. Press reservoir downward touching only the outer rim.DO NOT TOUCH THE INSIDE OF THE RESERVOIR WITH BARE HANDS, IT MUST REMAIN SANITARY.b) Reattach the faucets to the reservoir, making sure that the gaskets are in place.J. ALTERNATE FAUCETSA safer faucet that deters accidental dispensing of water by toddlers is available. This new faucet is simple and easy to use with one hand yet it adds a newmeasure of protection to your water cooler. See your dealer for details.WARNINGThe warranty for this machine is automatically void if any alteration, modification, or combination with any other machine or device is deemed to be the source of anyclaim. The Underwriters’ Laboratory Listing and CSA’s Certification may be void as the result of any alteration or modification. The manufacturer accepts no liabilityresulting from any alteration, modification, or combination with any other machine or device.EXCEPT AS SET FORTH HEREIN, THE MANUFACTURER MAKES NO OTHER WARRANTY, GUARANTEE OR AGREEMENT EXPRESSED, IMPLIED ORSTATUTORY, INCLUDING ANY IMPLIED WARRANTY OR MERCHANTIABILITY OR FITNESS FOR A PARTICULAR PURPOSE.030099-216 Rev D

/ 2

Related manuals for Oasis POU1RRHS