Carat / Gold BalancesInstruction ManualBalanzas Carat / GoldManual de InstruccionesBalances Carat / GoldGuide de I’utilisateurCarat / Gold -WaagenBedienungsanleitungBilancia Carat / GoldManuale d’instruzioni

safety precautions

initial calibration

menu navigation

sealing access to the balance settings

troubleshooting

technical data

specifications

limited warranty

precauciones de seguridad

technische daten

OHAUS Carat PAJ603 Instruction Manual

Introduction

Tools and Test Equipment Required

Balance Operation

Overview of the Display Indicators

Power On

The Load Cell

Connecting the RS232 Interface

RS232 Commands

Troubleshooting

Diagnostic Guide

Error Codes

Preventive Maintenance

Variations in Opening Pioneer Models

Load Cell Removal and Disassembly

Disassembly of Precision Balances with Internal Calibration

Removing Internal Calibration Weights

Reassembling the Internal Calibration Mechanism

Proper manner to grasp Load Cell when removing Weight Arm assembly

Service Fixture, screws and washers for 150g to 310g Precision balances

Precision Load Cell top

Position Sensor Board

Hanger

Magnets must be clean

Service Fixture for 510g to 4100g Precision Load Cell, attached to Hanger

Sideways Motion Stop Plate

When Position Sensor Board shows normal weight, tighten its screws

Removing the InCal Mechanism from InCal Analytical Balances

Bottom Housing with Load Cell, Weight Arms and Weights removed

Re-Installing Internal Calibration Components

Disassembling Analytical Load Cells

Shims are inserted between the Hanger and the Load Cell

Vertical Flexure and screws, Lock Plate, washers, and bushings, removed

Hanger with two screws

Contact Board with 3-wire ribbon cable soldered to it

A screw connects the Contact Board to the Load Cell

Position Sensor PC Board Removal/Replacement/Adjustment - Analytical

Reassembling Analytical Load Cells

Installing the Magnet Half

Insert shims between the Hanger and the Load Cell on both sides

Analytical InCal Load Cell with Top Bracket visible

Block Style Load Cell

Progressive Disassembly of Block Style Load Cells

Internal Calibration Testing

InCal Mechanism Removal

InCal Mechanism Installation

Removing Position Sensor

Removing the Block Style Load Cell from the Base Plate

Installing the Block Style Load Cell on the Base Plate

Removal and Installation of the Block Style Load Cell PC Board

Load Cell PCB-Temperature Sensor-Position Sensor assembly

Removing the Ratio Beam on Block Style Load Cells

Contact Board with cover holder off

Weight Arm Screws and Washers removed

Aluminum Sleeves removed

Installing the Ratio Beam on Block Style Load Cells

Ratio Beam Vane Slotted Area

Installing the InCal Weight Arm

Centering pins in Ratio Beam

Installing the Load Cell PCB-Temperature Sensor-Position Sensor

Position Sensor on the Magnet

Setting the Up/Down Stop Screw on Block Style Load Cells

Test Masses Required

Performance Tests

Off-Center Load Test

Off-Center Load Adjustment for Precision Models

Off-Center Load Adjustment for Analytical Models

Off-Center Load Adjustment for Block Style Models

Repeatability Test

Repeatability Worksheet

Linearity Test

Carat PAJ1003

Carat PAJ1003C

Carat PAJ2003

Carat PAJ2003C

Carat PAJ603

Carat PAJ603C

Cold PAJ3101

Cold PAJ4101

Gold PAJ2101

Gold PAJ2101C

Gold PAJ2102

Gold PAJ2102C

Gold PAJ3101C

Gold PAJ3102

Gold PAJ3102C

Gold PAJ4101C

Gold PAJ4102

Gold PAJ4102C

Gold PAJ812

Gold PAJ812C

OHAUS Carat PAJ603 Instruction Manual

Product

Learn More

Legal


Contents safety precautions initial calibration menu navigation sealing access to the balance settings troubleshooting technical data specifications limited warranty precauciones de seguridad technische daten	Carat / Gold BalancesInstruction ManualBalanzas Carat / GoldManual de InstruccionesBalances Carat / GoldGuide de I’utilisateurCarat / Gold -WaagenBedienungsanleitungBilancia Carat / GoldManuale d’instruzioni Next / 62