Nakanishi EM-3030T Operation Manual

Nakanishi EM-3030T Operation Manual Manual pdf 1 page image

OPERATION MANUALBrushless MotorThank you for purchasing the Brushless Motor " EM-3030T ". The E3000 CONTROLLER, Spindle, Motor Cordand Air Line Kit are required to drive this Brushless Motor. Read this and all the associated component OperationManuals carefully before use.Always keep this Operation Manual in a place where a user can referred to for reference at any time.Read these warnings and cautions carefully and only us e in the manner intended.These warnings and cautions are intended to avoid potential hazards that could result in personal injury to theoperator or damage to the device. These are classified as follows in accordance with the seriousness of the risk.Class Degree of RiskWARNING A safety hazard could result in bodily injury or damage to thedevice if the safety instructions are not properly followed.CAUTION A hazard that could result in light or moderate bodily injury ordamage to the device if the safety instructions are not followed.CAUTIONS FOR HANDLING AND OPERATION1.This Brushless Motor is not a hand tool. It is designed to be used on CNC machines or specialpurpose machines.Do not touch the cutting tool while it is running. It is very dangerous.Wear safety glasses, dust mask, and use a protective cover around the Brushless Motor wheneverthe Brushless Motor is rotating.Never connect, disconnect or touch the Power Cord Plug or Motor Cord Plug with wet hands. Thismay cause an electric shock.Never operate or handle the Brushless Motor and spindle until you have thoroughly read theOperation Manuals and safe operation has been confirmed.1) To prevent injuries / damages, check the Brushless Motor, spindle and cutting tool for properinstallation, before operating the Brushless Motor and spindle.2) Before disconnecting the Brushless Motor and spindle, always turn the control power offand turn the compressed air supply to the CONTROLLER off. Then it is safe to remove theBrushless Motor and spindle.When installing a Brushless Motor to a fixed base, make sure the fixed base is grounded in orderto avoid the risk of an electric shock.WARNINGDo not drop or hit this Brushless Motor, as shock can damage to the internal components.When cleaning a Brushless Motor, stop the Brushless Motor and remove debris with a soft brushor a cloth. Do not blow air into the Brushless Motor with compressed air as foreign particles orcutting debris may get into the ball bearing.Select suitable products or tools for all applications. Do not exceed the capabilities of theBrushless Motor or tools.Do not stop the supplied cooling air to the Brushless Motor during operation of the machine.Removing the air pressure from the Brushless Motor causes a loss of purging, allowing theBrushless Motor to ingest coolant and debris. This will cause damage to the Brushless Motor.Stop working immediately when abnormal rotation or unusual vibration are observed. Immediately,please check the content of section " 9. TROUBLESHOOTING ".Always check if the connection hose and supply air hose for damaged before and after operating.After installation, repair, initial operation, or long periods of non operation, please carry out break-in as follow. Start rotating slowly and over a short period of 15 - 20minutes, increase speedgradually until Maximum Allowable Motor Rotation Speed.Do not disassemble, modify or attempt to repair this Brushless Motor. Additional damage willoccur to the internal components. Service must be performed by NSK NAKANISHI or an authorizedservice center.When using this Brushless Motor for mass production, please consider the purchase of anadditional Brushless Motor to be used as a back-up in case of emergency.Securely connect the compressor supply connection hose to the Air Line Kit, and connectthe air hose to the Air Line Kit, the CONTROLLER and the Brushless Moor to avoid accidentaldisconnection during use.CAUTIONBASIC PACKAGE2.When opening the package, check if it includes all items listed in " Table. 1 Packing List Contents ". In the event ofany shortage, please contact either NAKANISHI (see the " 4. CONTACT US " section) or your local dealer.Table. 1 Packing List ContentsBrushless Motor1pc. Wrench (22 x 27) 1pc. Operation Manual1set2722取扱説明書OPERATION MANUALWARRANTY3.We provide a limited warranty for our products. We will repair or replace the products if the cause of failure is due tothe following manufactures defects. Please contact us or your local distributor for details.Defect in manufacturing.Any shortage of components in the package.Where damaged components are found when initially opening the package.(This shall not apply if the damage was caused by the negligence of a customer.)CONTACT US4.For your safety and convenience when purchasing our products, we welcome your questions.If you have any questions about operation, maintenance and repair of the product, please contact us.Company NameBusiness HoursU.S. Toll Free No.Telephone No.Fax No.Web Address:Industrial Div.: 8:30am to 17:00pm (CST)(closed Saturday, Sunday and Public Holidays): 800-585-4675: 847-843-7664: 847-843-7622: www.nskamericacorp.comContact UsContact UsFor U.S. MarketCompany NameBusiness HoursTelephone No.e-mail Address:: 8:00am to 17:00pm(closed Saturday, Sunday and Public Holidays): +81 (0) 289-64-3520: webmaster-ie@nsk-nakanishi.co.jpFor Other MarketsFEATURES5.The Brushless Motor housing is made from precision ground, hardened, stainless steel (SUS) with an outsidediameter of φ30mm.Excellent durability and high reliability are obtained by using a high-speed brushless motor, which eliminatesthe need for brush replacement and frequent maintenance.The maximum output is 350W.Air-cooling system with a small volume of air (30 / min) is used to prevent heat buildup and allows longcontinuous operation.SPECIFICATIONS AND DIMENSIONS6.6 - 1 SpecificationsModel EM-3030TMaximum Motor Rotation Speed 30,000min -1 (rpm)Max. Output 350WWeight 350gNoise Level at 1m distance Less than 70dB (A)Temperature Humidity Atmospheric PressureOperation Environment 0 - 40°C MAX.75%(No condensation) 800 - 1,060hPaTransportation and StorageEnvironment -10 - 50°C 10 - 85% 500 - 1,060hPa*Note : Motor Cord is sold separately.Please select the suitable motor cord length for your application.Do not exceed the Maximum Motor Rotation Speed (Refer to " 6 - 1 Specifications " ).This Brushless Motor should be connected to the Applicable CONTROLLER (Refer to " Table. 2Identifying the Applicable CONTROLLER ").If this Brushless Motor is connected to non applicable CONTROLLER, the Brushless Motor willnot rotate and Error " EL " (Incompatible Motor) will be displayed on the Digital Speed Indicator,indicating a " Detection of unsafe operating conditions " of the CONTROLLER.CAUTIONTable. 2 Identifying the Applicable CONTROLLERIdentifying Point Applicable CONTROLLER Non applicable CONTROLLERColor of Air Output JointFirst letter of the SerialNo. on the Rating Plate orBlue WhiteFirst letter : Other than " D "XXXXXXXDXXXXXXXFirst letter : " D "EM - 3030TOM-K0693EFirst letter : " D "DXXXXXXXMotor Cord*Note ~~Straight~~ ~~EMCD-3000-4M (4m) / 6M (6m) / 8M (8m)(The Air Hose of the same length is attached.) Angle EMCD - 3000A - 4M (4m) / 6M (6m) / 8M (8m)(The Air Hose of the same length is attached.)~~

~~Next~~

~~/ 2~~

Related manuals for Nakanishi EM-3030T