NEC PlasmaSync 42XC10 User Manual

Also see for PlasmaSync 60XC10: Brochure & specs Supplementary guide Brochure Brochure Brochure

NEC PlasmaSync 42XC10 User Manual Manual pdf 5 page image

English-2WARNINGTO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. DO NOT USE THISUNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGSCAN BE FULLY INSERTED.REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL.CAUTIONCAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM WALLSOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER CORDFROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.Th is symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock.Therefore, it is dangerous to make any kind of contact with any part inside this unit.Th is symbol alerts the user that important literature concerning the operation and maintenance of this unit has beenincluded. Therefore, it should be read carefully in order to avoid any problems.Important InformationCanadian Department ofCommunications Compliance StatementDOC: This Class B digital apparatus meets all requirements of the CanadianInterference-Causing Equipment Regulations.FCC Information1. Use the attached specified cables with the P426Y3(P42XC10),P506Y4(P50XC10) or P606Y5(P60XC10) color monitor so as not tointerfere with radio and television reception.(1) Please use the supplied power cord or equivalent toensure FCC compliance.(2) Please use shielded video signal cable,15-pin mini D-SUB to 15-pin mini D-SUBwith ferrite cores on both ends (not included).2. This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to part 15 of the FCC Rules. Theselimits are designed to provide reasonable protection against harmfulinterference in a residential installation. This equipment generates, uses,and can radiate radio frequency energy, and, if not installed and usedin accordance with the instructions, may cause harmful interference toradio communications. However, there is no guarantee that interferencewill not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can bedetermined by turning the equipment off and on, the user is encouragedto try to correct the interference by one or more of the followingmeasures:Reorient or relocate the receiving antenna.Increase the distance between the equipment andreceiver.Connect the equipment into an outlet on a circuitdifferent from that to which the receiver is connected.Consult your dealer or an experienced radio/TV technician for help.If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions. The user may find thefollowing booklet, prepared by the Federal Communications Commission,helpful: “How to Identify and Resolve Radio-TV Interference Problems.” Thisbooklet is available from the U.S. Government Printing Office, Washington,D.C., 20402, Stock No. 004-000-00345-4.WARNINGThis product equipped with a three-wire grounding (earthed) plug - a plugthat has a third (grounding) pin. This plug only fits a grounding-type poweroutlet. If you are unable to insert the plug into an outlet, contact a licensedelectrician to replace the outlet with a properly grounded one. Do not defeatthe safety purpose of the grounding plug.••••CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is notsupplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the ACvoltage of the power outlet and has been approved by and complies with the safety standard of your particular country.Plug Type North America EuropeanContinental U.K. Chinese JapanesePlug ShapeCountryVoltageU.S.A./Canada U.K. China JapanEU (except U.K.)120* 230 220 100230*When operating the PlasmaSync monitor with its AC 125-240V power supply, use a power supply cord that matches the powersupply voltage of the AC power outlet being used.