NEC NLT-40W Owner's Manual

Contents

NEC NLT-40W Owner's Manual Manual pdf 8 page image

16Sound ControlYou can select your preferred sound setting; Flat, Music,Movie or Speech and you can also adjust the soundfrequency of equalizer, balance. If you switch AVL to on,the set automatically keeps on an equal volume level evenif you change programme.1. Press the MENU button.2. Select the Sound menu, then press VOLÏq button.3. Press the PRxy button to select the desiredsound item; Equalizer, Balance, AVL Surround orheadphone Volume.4. Press the VOLÏq button to make desiredadjustment.5. Press the VOLÏq button in Equalizer to set theEqualizer.6. Press the PRxy button to select your preferredsetting ; Flat, Music, Movie, Speech or User.To set the Equalizer User.a. Select User by pressing the PRxy button.b. Select a sound band by pressing the VOLÏqbutton.c. Make appropriate sound level with the PRxybutton.d. Press the MENU button to return to precedingMENU and the TV/AV button to return to normalTV viewing.7. Select the Balance menu and adjust the balance ofspeakers.8. Select the AVL(Automatic Volume Leveler) menu Onor Off9. Select the Surround menu On or Off.10. Select the nVolume menu and adjust the volumefrom headphone.11. Select the Sub woofer menu to adjust the bassvolume.(It is possible when the Sub woofer isconnected to the set.)ż The sound Flat, Music, Movie and Speech areprogrammed for good sound reproduction at the factoryand cannot be changed.Auto Sound ControlSSM (Sound Status Memory)1. Press the SSM button.2. Press the SSM button repeatedly to select.Each press of the button changes the screen display as below.Flat ؋ Music ؋ Movie ؋ Speech ؋ UserƇƉ ȖȘ 5-6=<>)>SoundEqualizer ȘBalance 0AVL OffSurround OffnVolume 30Sub woofer 0ƇƉ 5-6=<>)>EqualizerFlatMusicMovieSpeechUser 3Pb17Other functionsTV, COMPONENT and S-VIDEO modes(You can’t set PC mode in this menu. Use the TV/AVbutton)External equipment inputs:S-VIDEO mode are used forvideo devices like VCRs, DVDs, etc.), COMPONENTmode is used for COMPONENT type devices.Note : If a VCR is connected to the antenna jack, use TVmode. See External Equipment Connection section.1. Press the MENU button.2. Select the Special menu.3. Press the PRxy button to select Input.4. Press the VOLÏq button to select TV,COMPONENT and S-VIDEO.COMPONENT : Component device connected to theCOMPONENT jack.S-VIDEO : S-VIDEO device connected to the TV'sS-VIDEO Input.To return to TV mode, press the TV/AV button.Alternatively you can select the TV, COMPONENT,S-VIDEO, PC-ANALOG or PC-DIGITAL mode bypressing the TV/AV button.Auto sleepIf you select Auto sleep on the set will automaticallyswitch itself to standby mode approximately ten minutesafter a TV Channel stops broadcasting.1. Press the MENU button, select the Special menu,then press VOLÏq button.2. Press the PRxy button to select Auto sleep.3. Press the VOLÏq button to select On.4. Press the TV/AV button to return to normal TVviewing.Blue backProgramme without a program signal appear in blue.Auto wide (Aspect Ratio Control)Press the ARC button to select a desired picture format.Each press of the ARC button, selects Auto Wide, 16:9,14:9, ZOOM, 1:1 and Auto wide mode.ƇƉ ȖȘ 5-6=<>)>SpecialInput TVAuto sleep OffBlue back OnAuto wide Off