ND-71075 (E)ISSUE 1STOCK # 152015Retrofit System Guideincludes NEAX ®1000 IVSJUNE, 2000NEC America, Inc.®

NEC NEAX 2000 IVS2 Retrofit Manual

account codes

call options

call waiting

NEAX 2000IVS2

installation procedure manual

neax2000 ivs

regulatory information

SAFETY INSTRUCTIONS

NEAX2000 IVS

INTRODUCTION

ISSUE

CHAPTER 1 GENERAL INFORMATION

TRUNKING DIAGRAM

SYSTEM CONFIGURATION

Figure 1-3 2-PIM Configuration for Floor Standing Installation

Figure 1-4 Maximum Configuration for Floor Standing Installation

Wall Mounting Installation

inch Rack Mounting Installation

EQUIPMENT NAME AND FUNCTION

Table 1-2 Installation Hardware Name and Function

Control Card

Application Processor Card

Line/Trunk Card

LINE CONDITIONS OF EACH TERMINAL

MOUNTING CONDITIONS OF CIRCUIT CARD

Control Card Mounting Conditions

Application Processor Card Mounting Conditions

Figure 1-10 Application Processor Card Mounting Slots (PIM1-7)

Line/Trunk Card Mounting Conditions

Figure 1-12 Line/Trunk Card Mounting Slots (PIM1-7)

CHAPTER 2 INSTALLATION

PRECAUTIONS

Static Electricity Guard

Figure 2-1 Static Electricity Guard (2 of 2)

Procedure for Unplugging/Plugging Circuit Cards

Turning Power ON

Turning Power OFF

PROCEDURE

Figure 2-2 Procedure Flowchart (2 of 2)

Stationary Equipment (For North America/Australia)

UNPACKING

WIRING AC CABLE TO TERMINALS

Figure 2-4 AC CORD Wiring for Two-Frame Configuration

Using Installation Cable

Figure 2-6 Installation Cable Wiring for Two-Frame Configuration

INSTALLATION OF MAIN EQUIPMENT

Figure 2-7 Floor Space

Figure 2-8 Cable Hole Location

Figure 2-9 Floor Marking for BASE PLATE (for Fixed Equipment)

Figure 2-11 Drilling Instructions for Anchor Bolt

Figure 2-12 Connection of BASE and BASE PLATE

Figure 2-13 Connection of PIM and BASE

Figure 2-14 Placing PIM on BASE TRAY

Figure 2-15 Connection of BUILD PLATE

Figure 2-16 Connection of FRONT STOPPER

Figure 2-17 Connection of Modules

Figure 2-18 Installation of MOUNTING BRACKET

Figure 2-19 Wall Marking for HANGER ASSEM

Figure 2-20 Hanging PIM to HANGER ASSEM

Figure 2-21 Detaching SIDE COVER (1 of 2)

Figure 2-21 Detaching SIDE PANEL (2 of 2)

Figure 2-22 Connection of 19" RACK BRACKET (A)

Figure 2-23 Mounting PIM to 19-inch Rack

Figure 2-24 Connection of 19" RACK BRACKET (B)

Figure 2-25 Mounting Multiple-PIM to 19-inch RACK

BUS Cable Connection

POWER CABLE CONNECTION

Connection of AC CORD-B

Connection of DC Power Cable

Figure 2-31 Mounting PZ-PW122 into PIM

Figure 2-32 Cable Connection between PZ-PW121/PZ-PW122 and BWB

Figure 2-33 PWR CA-A

Figure 2-35 Connection of PWR CA-A Cables

SUPPLY VOLTAGE CHECK AND HEAT RUN TEST

Power Routing

Checking for Supply Voltage

Figure 2-36 Confirming Output Voltage

BATTERY CONNECTION

Internal Battery Connection

Figure 2-37 Internal Battery Mounting (2 of 2)

Figure 2-38 Internal Battery Connection for Multiple-PIM Configuration

External / BATTM Battery Connection

Figure 2-40 Battery Mounted into BATTM

Figure 2-41 External/BATTM Battery Connection for Multiple-PIM Configuration

CABLE RUNNING TO MDF

MDF Cable

Table 2-2 MDF Cables for each PIM

Cable Running to External MDF

Figure 2-45 Cable Running to the External MDF (1 of 2)

Figure 2-45 Cable Running to the External MDF (2 of 2)

TERMINATION OF CABLES ON MDF

Location of Each LEN

LTC Connector Pin Arrangement

NEC NEAX 2000 IVS2 Retrofit Manual

Product

Learn More

Legal